Hearth and Home Technologies RUTHERFORD-42 Installing Side Molded Brick Panel-Herring- bone

Page 39

D. Installing Side Molded Brick Panel-Herring- bone

•If a gas line is to be installed, remove the knockouts in the inner firebox and in the outer shell on the side of your choice. Refer to dimension drawings for location of knockouts and Section 13.A. for gas provisions.

•Do NOT remove screen rods.

•Refer to Figure 11.2.

•Install lower side panel, tapered edge to the front. Align the front edge with the front of the column (or butted to the surround if installed).

•Install two T-brackets stem down into mortar line, do not tighten.

•Install upper side panel in the unit, tapered edge to the front. Position the bottom of panel behind the T-brackets. Install two T-brackets stem up into mortar lines, one Y- bracket on the front edge as shown. Do not tighten.

•Install two Z-brackets in the mortar joints across the top. Tighten these and all previously installed brackets.

•Install second side panel following the steps above.

Note: Use T-brackets as templates and drill pilot holes into the inner shell with the drill bit provided. Side panels must be installed first.

E. Installing Back Molded Brick Panel-Her- ringbone

•Refer to Figure 11.2.

•Set the grate brackets in place, 26.5 in. (673 mm) center to center.

•Install the lower back panel. Center from side to side.

•Install two T-brackets stem down into mortar line to hold lower back in position. Do not tighten.

•Install upper back panel. Position bottom of panel behind the previously installed T-brackets. Install three T-brackets stem side up into mortar line, do not tighten

•Install two Z-brackets in the mortar joints across the top. Tighten these and all previously installed brackets.

Front

 

 

Upper Side

Upper Back

 

Molded Brick Panel

Molded Brick Panel

 

 

Lower Back

 

 

Molded Brick Panel

 

Lower Side

 

 

Molded Brick Panel

 

 

 

Grate Brackets

 

 

Hearth Molded Brick Panel

 

Figure 11.2 Herringbone Molded Brick Panel

 

 

Heat & Glo • RUTHERFORD-42 • 4059-309 Rev G • 11/08

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Fire Risk Hot screen/mesh and glass doors will cause burnsListing Label Information/Location GrateNumber Table of Contents CONDITIONS, Exclusions & Limitation of Liability ÎWarranty Hearth & Home Technologies Limited WarrantyHeat & Glo RUTHERFORD-42 4059-309 Rev G 11/08 Combustible Materials Listing and Code ApprovalsAppliance Certification Non-Combustible MaterialsYour Fireplace Operating InstructionsFirescreen Seasoned WoodStarting a Fire GrateClear Space Glass DoorsVented Gas Log Sets & Gas Log Lighters Optional ComponentsHardwood vs Softwood Wood FuelMaintainance and Service Chimney Inspection/CleaningDisposal of Ashes Frequency As desired Glass CleaningCheck Firebox Molded Brick Panel Inspect GrateStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedDesign and Installation Considerations DraftNegative Pressure Recommended Chimney Locations Locating your Fireplace & ChimneyTools and Supplies Needed Inspect Fireplace and ComponentsTypical Fireplace Components Select Fireplace Location Framing & ClearancesAir Space Clearances ClearancesFrame the Fireplace Sidewalls/SurroundsPlace Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the FireplaceYES Outside Air Installation Install Outside Air KitChimney Assembly Height of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssembling Chimney Sections Assemble Chimney SectionsInstalling the Ceiling Firestop Install Ceiling FirestopsPrepare Attic Insulation Shield Install Attic Insulation ShieldComplete Installation Install FlashingCut Out Hole in Roof Flat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyST1175 Square Termination Cap Install Termination CapTCT1175 Terra Cotta Cap Shrouds Radiation ShieldField Constructed Shrouds Mailbox Style Shroud radiation shield required Install Back Molded Brick Panel-Traditional Installation of Molded Brick PanelInstall Hearth Molded Brick Panel Install Side Molded Brick Panel-TraditionalInstalling Back Molded Brick Panel-Her- ringbone Installing Side Molded Brick Panel-Herring- boneInstall Screens Install MortarFinishing Hearth Extension= 1/k x inches of thickness Finishing Materials NoncombustibleFraming Material Equivalent insulationNon-combustible Sealant Noncombustible Facing Finishing MaterialCombustible Mantel 14 Secure to Framing Mantel, Adding Extra SupportBrick Front Gas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provision Wood Burning InsertsReference Materials Fireplace DimensionsID6 Insulated Duct .4 mm i.d 1067 mm UD6 Uninsulated Duct Catalog # Chimney Components15-1/4 387 mm 31-3/4 806 mm 34-5/8 879 mm CT56 Chase Top Parts ServiceDo not Discard this Manual

RUTHERFORD-42 specifications

Hearth and Home Technologies presents the RUTHERFORD-42, an exceptional gas fireplace that combines sophisticated design with advanced functionality. This model signifies the perfect blend of aesthetics and performance, making it a favored choice for homeowners seeking to enhance their living spaces with the warmth and comfort of a fireplace.

One of the primary features of the RUTHERFORD-42 is its impressive viewing area, measuring 42 inches wide. This expansive glassfront design offers a stunning visual display of the flames, creating a cozy ambiance that enhances any room. The fireplace is framed with a stylish surround that can be customized to match various interior styles, adding a touch of elegance to contemporary and traditional homes alike.

Equipped with advanced technology, the RUTHERFORD-42 ensures efficient heat output while maintaining ease of use. The fireplace features an electronic ignition system that provides reliability and convenience with a simple push-button start. Additionally, it incorporates a thermostat remote control, allowing users to easily regulate the temperature from anywhere in the room. This functionality not only enhances user comfort but also improves energy efficiency.

The unit is designed with a powerful yet quiet fan that circulates warm air throughout the space, ensuring even heat distribution. This makes the RUTHERFORD-42 an excellent option for supplemental heating in larger rooms, providing both style and warmth during colder months.

Safety is a paramount concern in all Hearth and Home Technologies products, and the RUTHERFORD-42 is no exception. It includes safety screens that protect against accidental contact with the flames, ensuring peace of mind while enjoying the fire’s warmth. Furthermore, it complies with stringent safety standards, making it a reliable choice for families.

In terms of aesthetics, the RUTHERFORD-42 offers various media options, including glass, ceramic logs, and stone, allowing homeowners to personalize the fire's appearance to align with their home’s décor. The fireplace is also available in different finishes, giving users the flexibility to create a focal point that perfectly complements their interior design.

Overall, the Hearth and Home Technologies RUTHERFORD-42 is a standout model that combines cutting-edge technology, safety features, and design flexibility, making it an excellent choice for anyone looking to add a stylish and functional gas fireplace to their home.
Top Page Image Contents