Hearth and Home Technologies RH-36 Series Install Outside Air Kit, Outside Air Installation

Page 23

E. Install Outside Air Kit

Optional.

Keep duct runs short and straight to minimize restriction. A small dip is acceptable for a cold air trap.

The outside air kit must be installed on the left hand side of the fireplace.

Locate the outside air hood in a clear area, preferably into prevailing wind during the heating season. Refer to Figure 5.2.

Install as shown in Figures 7.3, 7.4 and 7.5.

The air duct may be run vertically.

The outside air hood must be at least 3 ft (.91 m) below the top of the uppermost chimney section.

CAUTION! Risk of Fire or Asphyxiation! DO NOT draw outside combustion air from wall, floor or ceiling cavity, or enclosed spaces such as an attic or garage.

DO NOT place outside air hood close to exhaust vents or chimneys. Fumes or odor could be drawn into the room through the fireplace.

Locate outside air inlet to prevent blockage from leaves, snow/ice, or other debris. Blockages could cause combustion air starvation.

Flexible Duct (not supplied)

 

 

Outside Air

Outside Air

 

Plate

 

Assembly

Hood

2 Wire Ties

 

Figure 7.5 Outside Air Installation

Heat & Glo • RH-36/RH-424044-153 • Rev W • 11/08

23

Image 23
Contents Fire Risk Wood Burning FireplaceOperation Hot screen/mesh and glass doors will cause burnsNumber Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited WarrantyHeat & Glo RH-36/RH-42 4044-153 Rev W 11/08 Combustible Materials Listing and Code ApprovalsAppliance Certification Non-Combustible MaterialsHot glass will cause burns Operating InstructionsYour Fireplace Firescreen Seasoned WoodStarting a Fire GrateClear Space Glass DoorsVented Gas Log Sets & Gas Log Lighters Optional ComponentsWood Fuel Creosote Formation and Need for Removal Maintainance and ServiceChimney Inspection/Cleaning Disposal of AshesFrequency As desired Glass CleaningCheck Firebox Refractory Inspect GrateStart Fire Problems Possible Cause Solution Troubleshooting GuideGetting Started Installer GuideNegative Pressure Design and Installation ConsiderationsDraft Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyInspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Select Fireplace Location Mm all configurationsFraming & Clearances Clearances to Combustible Materials ClearancesModel # Opening Mensions Sidewalls/SurroundsFrame the Fireplace Outside DiPlace Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the FireplaceYES Ft min. from top of uppermost chimney section to air inletOutside Air Installation Install Outside Air KitMaintain minimum height of chimney above roof Chimney AssemblyHeight of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssemble Chimney Sections Install Chimney Air KitInstalling the Ceiling Firestop Install Ceiling FirestopsPrepare Attic Insulation Shield Install Attic Insulation ShieldCut out Hole in Roof Complete InstallationInstall Flashing Following steps should be skipped if using a chaseFlat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsCaulk all seams to prevent leaks Refer to Figure Install Fireplace & ChimneyInstall Chase Top Install as per Sections 7ST375 Square Termination Cap Install Termination CapTCT375 Terra Cotta Cap TS345/TS345P Square Termination CapOpen Top Shroud TR342 caps require radiation shield ShroudsRadiation Shield Field Constructed ShroudsRoofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield requiredRefer to .2 for hearth extension insulation alternatives FinishingHearth Extension = 1/k x inches of thicknessMinimum between Raised Hearth Extension FramingNoncombustible Finishing Materials Non-combustible SealantIn. Micore or equivilent insulation Finishing MaterialClearances to Mantels or other Combustibles above Fireplace Combustible MantelModel Outside Di- mensionsGas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provision Wood Burning InsertsModel # Fireplace DimensionsReference Materials Air Kit Parts 1321 mm 406 mm1676 mm 508 mm 13 mm ID4 Insulated Duct Mm i.d 1067 mm UD4 Uninsulated DuctCatalog # Chimney Components305 mm 24-5/8 625 mm 787 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm10-1/2 267 mm 305 mm 27-3/8 24-5/8 695 mm 625 mm10-7/8 276 mm Parts Service11/08 Heat & Glo RH-36/RH-42 4044-153 RevDo not Discard this Manual

RH-36 Series specifications

Hearth and Home Technologies has long been an industry leader in innovative heating solutions, and the RH-36 Series exemplifies this commitment to quality and performance. Designed to provide both comfort and efficiency, the RH-36 Series wood-burning fireplace inserts combine advanced technologies with timeless aesthetics, making them a popular choice among homeowners.

One of the standout features of the RH-36 Series is its impressive heat output. With a BTU rating that allows it to efficiently warm large spaces, this appliance is perfect for those chilly winter nights. The expansive firebox is designed to accommodate larger logs, thus extending burn times and reducing the frequency of refueling. This not only enhances convenience but also promotes a more sustainable approach to home heating.

The RH-36 Series also integrates the company’s patented Clean Burn Technology, which maximizes combustion efficiency. This system ensures that the wood is burned at optimal temperatures, resulting in less smoke and emissions. More so, this technology decreases creosote buildup within the chimney, enhancing safety and reducing the need for frequent maintenance.

In terms of aesthetics, the RH-36 Series doesn’t disappoint. Its large glass viewing area showcases the mesmerizing flames, creating a cozy atmosphere in any room. The fireplace insert is available in various finishes and door options, allowing homeowners to customize the look to suit their decor. Whether you prefer a traditional style or a modern finish, the RH-36 can fit seamlessly into your living space.

Furthermore, the RH-36 incorporates user-friendly features that enhance the overall experience. The easy-to-access ash pan allows for quick cleanup and maintenance, while the adjustable air control provides flexibility in regulating the burn rate, allowing users to create the desired ambiance with ease.

In conclusion, the Hearth and Home Technologies RH-36 Series is designed for those who value efficiency, safety, and aesthetic appeal in their heating solutions. With advanced technologies like Clean Burn, excellent heat output, customizable designs, and convenient features, this series stands as a pinnacle of wood-burning fire inserts, promising to deliver warmth and beauty to any home. Whether for cozy family gatherings or peaceful evenings, the RH-36 is a versatile choice that meets diverse heating needs while elevating home interiors.