Hearth and Home Technologies RH-36 Series Assemble Chimney Sections, Install Chimney Air Kit

Page 27

C. Assemble Chimney Sections

WARNING! Risk of Fire! DO NOT install substitute or damaged chimney components.

•Use only those components described in this manual.

Substitute or damaged chimney components could impair safe operation and cause overheating and fire.

•Support the pipe during construction and check to be sure inadvertent loading has not dislodged the chimney section from the fireplace or at any chimney joint.

•Attach a straight chimney section or an offset to the top of the fireplace.

•Place inner flue to the inside of the chimney section below it. Place the outer casing outside the outer casing of the chimney section below it. Refer to Figure 8.4.

NOTICE: Chimney sections cannot be disassembled once locked together. Plan ahead!

•Lock chimney sections and/or offsets/returns together by pushing downward until the top section meets the stop bead on the lower section.

•Pull on the top section to make sure it is fully engaged and will not separate.

•You may use #6 or #8 sheet metal screws no longer than 1/2 in. (13 mm) to fasten chimney sections together. Do NOT penetrate inner flue.

WARNING! Risk of Fire! You MUST use screws (pro- vided) to fasten offset/returns to chimney sections to keep the chimney parts from twisting. Failure to do so could cause fire.

•Fasten offset/returns to chimney sections. Insert the screws (provided) through the predrilled holes. Do NOT penetrate inner flue.

•Secure chimney returns with hanger straps provided; fasten to studs or joists.

•Vertical straight runs of chimney must be supported every 35 ft (10.7 m).

D. Install Chimney Air Kit

•Required in Canada.

•Follow instructions provided with this accessory.

Figure 8.4 Assembling Chimney Sections

Heat & Glo • RH-36/RH-42 • 4044-153 • Rev W • 11/08

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Fire Risk Wood Burning FireplaceOperation Hot screen/mesh and glass doors will cause burnsListing Label Information/Location GrateNumber Table of Contents Installer GuideUser Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited WarrantyHeat & Glo RH-36/RH-42 4044-153 Rev W 11/08 Combustible Materials Listing and Code ApprovalsAppliance Certification Non-Combustible MaterialsOperating Instructions Your FireplaceHot glass will cause burns Firescreen Seasoned WoodStarting a Fire GrateClear Space Glass DoorsVented Gas Log Sets & Gas Log Lighters Optional ComponentsWood Fuel Creosote Formation and Need for Removal Maintainance and ServiceChimney Inspection/Cleaning Disposal of AshesFrequency As desired Glass CleaningCheck Firebox Refractory Inspect GrateStart Fire Problems Possible Cause Solution Troubleshooting GuideGetting Started Installer GuideDesign and Installation Considerations DraftNegative Pressure Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyTools and Supplies Needed Fireplace System RequirementsInspect Fireplace and Components Mm all configurations Framing & ClearancesSelect Fireplace Location Clearances to Combustible Materials ClearancesModel # Opening Mensions Sidewalls/SurroundsFrame the Fireplace Outside DiPlace Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the FireplaceYES Ft min. from top of uppermost chimney section to air inletOutside Air Installation Install Outside Air KitMaintain minimum height of chimney above roof Chimney AssemblyHeight of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssemble Chimney Sections Install Chimney Air KitInstalling the Ceiling Firestop Install Ceiling FirestopsPrepare Attic Insulation Shield Install Attic Insulation ShieldCut out Hole in Roof Complete InstallationInstall Flashing Following steps should be skipped if using a chaseFlat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsCaulk all seams to prevent leaks Refer to Figure Install Fireplace & ChimneyInstall Chase Top Install as per Sections 7ST375 Square Termination Cap Install Termination CapTCT375 Terra Cotta Cap TS345/TS345P Square Termination CapOpen Top Shroud TR342 caps require radiation shield ShroudsRadiation Shield Field Constructed ShroudsRoofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield requiredRefer to .2 for hearth extension insulation alternatives FinishingHearth Extension = 1/k x inches of thicknessMinimum between Raised Hearth Extension FramingNoncombustible Finishing Materials Non-combustible SealantIn. Micore or equivilent insulation Finishing MaterialClearances to Mantels or other Combustibles above Fireplace Combustible MantelModel Outside Di- mensionsGas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provision Wood Burning InsertsFireplace Dimensions Reference MaterialsModel # Air Kit Parts 1321 mm 406 mm1676 mm 508 mm 13 mm ID4 Insulated Duct Mm i.d 1067 mm UD4 Uninsulated DuctCatalog # Chimney Components305 mm 24-5/8 625 mm 787 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm10-1/2 267 mm 305 mm 27-3/8 24-5/8 695 mm 625 mm10-7/8 276 mm Parts Service11/08 Heat & Glo RH-36/RH-42 4044-153 RevDo not Discard this Manual

RH-36 Series specifications

Hearth and Home Technologies has long been an industry leader in innovative heating solutions, and the RH-36 Series exemplifies this commitment to quality and performance. Designed to provide both comfort and efficiency, the RH-36 Series wood-burning fireplace inserts combine advanced technologies with timeless aesthetics, making them a popular choice among homeowners.

One of the standout features of the RH-36 Series is its impressive heat output. With a BTU rating that allows it to efficiently warm large spaces, this appliance is perfect for those chilly winter nights. The expansive firebox is designed to accommodate larger logs, thus extending burn times and reducing the frequency of refueling. This not only enhances convenience but also promotes a more sustainable approach to home heating.

The RH-36 Series also integrates the company’s patented Clean Burn Technology, which maximizes combustion efficiency. This system ensures that the wood is burned at optimal temperatures, resulting in less smoke and emissions. More so, this technology decreases creosote buildup within the chimney, enhancing safety and reducing the need for frequent maintenance.

In terms of aesthetics, the RH-36 Series doesn’t disappoint. Its large glass viewing area showcases the mesmerizing flames, creating a cozy atmosphere in any room. The fireplace insert is available in various finishes and door options, allowing homeowners to customize the look to suit their decor. Whether you prefer a traditional style or a modern finish, the RH-36 can fit seamlessly into your living space.

Furthermore, the RH-36 incorporates user-friendly features that enhance the overall experience. The easy-to-access ash pan allows for quick cleanup and maintenance, while the adjustable air control provides flexibility in regulating the burn rate, allowing users to create the desired ambiance with ease.

In conclusion, the Hearth and Home Technologies RH-36 Series is designed for those who value efficiency, safety, and aesthetic appeal in their heating solutions. With advanced technologies like Clean Burn, excellent heat output, customizable designs, and convenient features, this series stands as a pinnacle of wood-burning fire inserts, promising to deliver warmth and beauty to any home. Whether for cozy family gatherings or peaceful evenings, the RH-36 is a versatile choice that meets diverse heating needs while elevating home interiors.
Top Page Image Contents