Hearth and Home Technologies RH-36 Series owner manual Heat & Glo RH-36/RH-42 4044-153 Rev W 11/08

Page 5

This limited warranty does not extend to or include surface ?nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, ?rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of the metal surfaces, cast iron components, baf?es, ?repots, doors, or ?rebox area are not covered by this warranty.

Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to this noise are not covered by this warranty.

HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or maintenance of the appliance not in accordance with the installation instructions; operating instructions and the listing agent identi?cation label furnished with the appliance; (2) installation which does not comply with local building codes; (3) shipping, improper handling, improper operation, abuse, misuse, accident or unworkmanlike repairs; (4) environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure

or handling devices such as exhaust fans or forced air furnaces or other such causes; (5) use of fuels other than those speci?ed in the operating instructions; (6) installation or use of components not supplied with the appliance or any other components not expressly authorized and approved by HHT; and/or (7) modi?cation of the appliance not expressly authorized and approved by HHT in writing.

This warranty does not apply to non-HHT venting components, hearth components or other accessories used in conjunction with the installation of this product.

This warranty is void if the appliance has been over-?red or operated in atmospheres contaminated by chlorine, ?uorine, or other damaging chemicals the appliance is subject to prolonged periods of dampness or condensation, or there is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation.

HHT’s liability under this warranty is limited to the replacement and repair of defective components or workmanship during the applicable period. HHT may fully discharge all of its obligations under such warranties by repairing the defective component(s) at HHT’s discretion. Shipping costs are not covered under this warranty.

Some states do not allow exclusions or limitation of incidental or consequential damages, so those limitations may not apply to you. This warranty gives you speci?c rights; you may also have other rights, which vary from state to state.

EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE WARRANTY SPECIFIED ABOVE.

This Limited Warranty is effective on all HHT appliances sold after September 01, 2008 and supersedes any and all warranties currently in existence.

If warranty service is needed, you should contact your installing dealer. If the installing dealer is unable to provide necessary parts or components, contact the nearest authorized HHT dealer or supplier.

4021-645A 09-01-08

Page 2 of 2

Heat & Glo • RH-36/RH-424044-153 • Rev W • 11/08

5

Image 5
Contents Operation Wood Burning FireplaceHot screen/mesh and glass doors will cause burns Fire RiskNumber Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited WarrantyHeat & Glo RH-36/RH-42 4044-153 Rev W 11/08 Appliance Certification Listing and Code ApprovalsNon-Combustible Materials Combustible MaterialsHot glass will cause burns Operating InstructionsYour Fireplace Starting a Fire Seasoned WoodGrate FirescreenVented Gas Log Sets & Gas Log Lighters Glass DoorsOptional Components Clear SpaceWood Fuel Chimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Creosote Formation and Need for RemovalCheck Firebox Refractory Glass CleaningInspect Grate Frequency As desiredStart Fire Problems Possible Cause Solution Troubleshooting GuideGetting Started Installer GuideNegative Pressure Design and Installation ConsiderationsDraft Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyInspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Select Fireplace Location Mm all configurationsFraming & Clearances Clearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsOutside Di Model # Opening MensionsThings to Consider Installation of FireplacePosition the Fireplace Place Protective Metal Hearth StripsYES Ft min. from top of uppermost chimney section to air inletOutside Air Installation Install Outside Air KitMaintain minimum height of chimney above roof Chimney AssemblyHeight of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssemble Chimney Sections Install Chimney Air KitInstalling the Ceiling Firestop Install Ceiling FirestopsPrepare Attic Insulation Shield Install Attic Insulation ShieldInstall Flashing Complete InstallationFollowing steps should be skipped if using a chase Cut out Hole in RoofFlat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyInstall as per Sections 7 Caulk all seams to prevent leaks Refer to FigureST375 Square Termination Cap Install Termination CapTCT375 Terra Cotta Cap TS345/TS345P Square Termination CapRadiation Shield ShroudsField Constructed Shrouds Open Top Shroud TR342 caps require radiation shieldRoofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield requiredHearth Extension Finishing= 1/k x inches of thickness Refer to .2 for hearth extension insulation alternativesMinimum between Raised Hearth Extension FramingNoncombustible Finishing Materials Non-combustible SealantIn. Micore or equivilent insulation Finishing MaterialClearances to Mantels or other Combustibles above Fireplace Combustible MantelModel Outside Di- mensionsGas Log/Lighter Provision AccessoriesWood Burning Inserts Gas Code, Ansi Z223.1Model # Fireplace DimensionsReference Materials 1676 mm 508 mm 13 mm 1321 mm 406 mmID4 Insulated Duct Mm i.d 1067 mm UD4 Uninsulated Duct Air Kit PartsCatalog # Chimney Components10-1/2 267 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm305 mm 27-3/8 24-5/8 695 mm 625 mm 305 mm 24-5/8 625 mm 787 mm10-7/8 276 mm Parts Service11/08 Heat & Glo RH-36/RH-42 4044-153 RevDo not Discard this Manual

RH-36 Series specifications

Hearth and Home Technologies has long been an industry leader in innovative heating solutions, and the RH-36 Series exemplifies this commitment to quality and performance. Designed to provide both comfort and efficiency, the RH-36 Series wood-burning fireplace inserts combine advanced technologies with timeless aesthetics, making them a popular choice among homeowners.

One of the standout features of the RH-36 Series is its impressive heat output. With a BTU rating that allows it to efficiently warm large spaces, this appliance is perfect for those chilly winter nights. The expansive firebox is designed to accommodate larger logs, thus extending burn times and reducing the frequency of refueling. This not only enhances convenience but also promotes a more sustainable approach to home heating.

The RH-36 Series also integrates the company’s patented Clean Burn Technology, which maximizes combustion efficiency. This system ensures that the wood is burned at optimal temperatures, resulting in less smoke and emissions. More so, this technology decreases creosote buildup within the chimney, enhancing safety and reducing the need for frequent maintenance.

In terms of aesthetics, the RH-36 Series doesn’t disappoint. Its large glass viewing area showcases the mesmerizing flames, creating a cozy atmosphere in any room. The fireplace insert is available in various finishes and door options, allowing homeowners to customize the look to suit their decor. Whether you prefer a traditional style or a modern finish, the RH-36 can fit seamlessly into your living space.

Furthermore, the RH-36 incorporates user-friendly features that enhance the overall experience. The easy-to-access ash pan allows for quick cleanup and maintenance, while the adjustable air control provides flexibility in regulating the burn rate, allowing users to create the desired ambiance with ease.

In conclusion, the Hearth and Home Technologies RH-36 Series is designed for those who value efficiency, safety, and aesthetic appeal in their heating solutions. With advanced technologies like Clean Burn, excellent heat output, customizable designs, and convenient features, this series stands as a pinnacle of wood-burning fire inserts, promising to deliver warmth and beauty to any home. Whether for cozy family gatherings or peaceful evenings, the RH-36 is a versatile choice that meets diverse heating needs while elevating home interiors.