Hearth and Home Technologies RH-36 Series owner manual Accessories, Gas Log/Lighter Provision

Page 44

12 Accessories

A. Gas Log/Lighter Provision

WARNING! Fire and/or Asphyxiation Risk! Use with solid wood fuel or decorative gas appliance only. Gas fire generates fumes.

•DO NOT install unvented gas logs

•Damper must be locked fully open when gas logs are installed

A certified gas log lighter or decorative gas log set can be installed in this fireplace.

•Maximum input is 100,000 BTU/hr.

•Decorative gas appliance must be certified to ANSI Z21.60 “Standard for Decorative Gas Appliances for Installation in Vented Fireplaces”.

•Must be installed in accordance with the National Fuel

Gas Code, ANSI Z223.1.

•A gas log set must incorporate a gas shutoff.

•Gas Log set requires the damper to be locked fully open.

•A listed automatic damper system with safety interlock may be used in this fireplace with only compatible, listed gas log sets. See damper system manufacturer’s insturctions.

•Knockouts are provided on both sides of the fireplace and in refractories for 1/2 in. (13 mm) iron pipe.

•Seal refractory around pipe with fireplace mortar or a non-combustible sealant.

B. Wood Burning Inserts

WARNING! Risk of Fire! Improper installation of wood in- serts may cause fireplace or chimney system to overheat.

If a wood burning insert is being installed in this fireplace, Hearth & Home Technologies recommends full reline of the chimney.

•Cooling air openings at the top of the chimney must not be obstructed in any manner.

•Hearth & Home Technologies recommends securing the reline at the top of the flue and using the cap certified for use with this fireplace system.

Firebox

Refractory

Seal with fireplace mortar or non-combust- ible sealant

Outer Shell

of Fireplace

Maintain air clearance to combustibles.

Combustible

Materials

Gas Line

Repack

Insulation

Knockout

Gas Line

4 in. (102 mm)

1 1/2 in. (38 mm) air space around

pipe

Combustible materials may be located at zero clearance to gas line beyond 4 in. (102 mm) from fireplace side.

Figure 12.1 Gas Line Installation

44

Heat & Glo • RH-36/RH-42 • 4044-153 • Rev W • 11/08

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Wood Burning Fireplace OperationHot screen/mesh and glass doors will cause burns Fire RiskNumber Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHeat & Glo RH-36/RH-42 4044-153 Rev W 11/08 Listing and Code Approvals Appliance CertificationNon-Combustible Materials Combustible MaterialsHot glass will cause burns Operating InstructionsYour Fireplace Seasoned Wood Starting a FireGrate FirescreenGlass Doors Vented Gas Log Sets & Gas Log LightersOptional Components Clear SpaceWood Fuel Maintainance and Service Chimney Inspection/CleaningDisposal of Ashes Creosote Formation and Need for RemovalGlass Cleaning Check Firebox RefractoryInspect Grate Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionInstaller Guide Getting StartedNegative Pressure Design and Installation ConsiderationsDraft Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsInspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Select Fireplace Location Mm all configurationsFraming & Clearances Clearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplaceOutside Di Model # Opening MensionsInstallation of Fireplace Things to ConsiderPosition the Fireplace Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet YESInstall Outside Air Kit Outside Air InstallationChimney Assembly Maintain minimum height of chimney above roofChimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleInstall Chimney Air Kit Assemble Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield Prepare Attic Insulation ShieldComplete Installation Install FlashingFollowing steps should be skipped if using a chase Cut out Hole in RoofChimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall as per Sections 7 Caulk all seams to prevent leaks Refer to FigureInstall Termination Cap ST375 Square Termination CapTS345/TS345P Square Termination Cap TCT375 Terra Cotta CapShrouds Radiation ShieldField Constructed Shrouds Open Top Shroud TR342 caps require radiation shieldMailbox Style Shroud radiation shield required Roofed Style Shroud radiation shield requiredFinishing Hearth Extension= 1/k x inches of thickness Refer to .2 for hearth extension insulation alternativesRaised Hearth Extension Framing Minimum betweenNon-combustible Sealant Noncombustible Finishing MaterialsFinishing Material In. Micore or equivilent insulationCombustible Mantel Clearances to Mantels or other Combustibles above FireplaceOutside Di- mensions ModelAccessories Gas Log/Lighter ProvisionWood Burning Inserts Gas Code, Ansi Z223.1Model # Fireplace DimensionsReference Materials 1321 mm 406 mm 1676 mm 508 mm 13 mmID4 Insulated Duct Mm i.d 1067 mm UD4 Uninsulated Duct Air Kit PartsChimney Components Catalog #Effective Outside Height Diameter 10-1/2 121 mm 267 mm 10-1/2 267 mm305 mm 27-3/8 24-5/8 695 mm 625 mm 305 mm 24-5/8 625 mm 787 mm10-7/8 276 mm Service PartsHeat & Glo RH-36/RH-42 4044-153 Rev 11/08Do not Discard this Manual

RH-36 Series specifications

Hearth and Home Technologies has long been an industry leader in innovative heating solutions, and the RH-36 Series exemplifies this commitment to quality and performance. Designed to provide both comfort and efficiency, the RH-36 Series wood-burning fireplace inserts combine advanced technologies with timeless aesthetics, making them a popular choice among homeowners.

One of the standout features of the RH-36 Series is its impressive heat output. With a BTU rating that allows it to efficiently warm large spaces, this appliance is perfect for those chilly winter nights. The expansive firebox is designed to accommodate larger logs, thus extending burn times and reducing the frequency of refueling. This not only enhances convenience but also promotes a more sustainable approach to home heating.

The RH-36 Series also integrates the company’s patented Clean Burn Technology, which maximizes combustion efficiency. This system ensures that the wood is burned at optimal temperatures, resulting in less smoke and emissions. More so, this technology decreases creosote buildup within the chimney, enhancing safety and reducing the need for frequent maintenance.

In terms of aesthetics, the RH-36 Series doesn’t disappoint. Its large glass viewing area showcases the mesmerizing flames, creating a cozy atmosphere in any room. The fireplace insert is available in various finishes and door options, allowing homeowners to customize the look to suit their decor. Whether you prefer a traditional style or a modern finish, the RH-36 can fit seamlessly into your living space.

Furthermore, the RH-36 incorporates user-friendly features that enhance the overall experience. The easy-to-access ash pan allows for quick cleanup and maintenance, while the adjustable air control provides flexibility in regulating the burn rate, allowing users to create the desired ambiance with ease.

In conclusion, the Hearth and Home Technologies RH-36 Series is designed for those who value efficiency, safety, and aesthetic appeal in their heating solutions. With advanced technologies like Clean Burn, excellent heat output, customizable designs, and convenient features, this series stands as a pinnacle of wood-burning fire inserts, promising to deliver warmth and beauty to any home. Whether for cozy family gatherings or peaceful evenings, the RH-36 is a versatile choice that meets diverse heating needs while elevating home interiors.
Top Page Image Contents