Hearth and Home Technologies RH-36 Series owner manual Chimney Components, Catalog #

Page 47

C. Chimney Components

The following pictures show only those chimney components which may be safely used with this ﬁreplace.

CAK4A		Chimney Air Kit
ID4		Insulated Duct/Outside Air

UD4		Uninsulated Duct/Outside Air
SL306		Chimney Section - 6 in. (152 mm) long
SL312		Chimney Section - 12 in. (305 mm) long

SL318		Chimney Section - 18 in. (457 mm) long
SL324		Chimney Section - 24 in. (610 mm) long

SL336		Chimney Section - 36 in. (914 mm) long
SL348		Chimney Section - 48 in. (1219 mm) long

SL3		Chimney Stabilizer
SL315		Chimney Offset/Return - 15 deg
SL330		Chimney Offset/Return - 30 deg

FS338		Ceiling Firestop - Straight
FS339		Ceiling Firestop - 15 deg

FS340		Ceiling Firestop - 30 deg
AS8		SL300 Straight Attic Insulation Shield, 24 in. (610 mm)

JB877		Chimney Joint Band
CB876		Chimney Bracket

RF370		Roof Flashing - Flat to 6/12 Pitch
RF371		Roof Flashing - 6/12 to 12/12 Pitch
TR344		Round Termination Cap

TR342		Round Telescoping Termination Cap
ST375		Square Termination Cap

TS345		Square Termination Cap
TS345P		Square Termination Cap - Painted

TCT375		Terra Cotta Termination Cap
CT35		Chase Top
LDS33		Decorative Shroud - 3 ft x 3 ft (.91 m x .91 m)

LDS46		Decorative Shroud - 4 ft x 6 ft (1.22 m x 1.83 m)
LDS-BV		Decorative Shroud - 26 in. x 26 in. (660 mm x 660 mm)

		Field Constructed Shrouds (See “Woodburning
		Termination Cap”)
CT-3A		Adapter - May be used with the following copper caps
						CT-King

						CT-Queen

					CT-Bishop-I

					CT-Bishop-II

					CT-Knight-I

						CT-Pawn

		12 in.				12 in.
		12 in.				(305 mm)
	(305 mm)					(305 mm)
	(305 mm)
5-1/4 in.
5-1/4 in.
(133 mm)						4 in. (102 mm)
(133 mm)
	10-1/2 in.
	10-1/2 in.
	(287 mm)

ID4 Insulated Duct

4 in. (102 mm) i

42 in.

(1067 mm)

UD4 Uninsulated Duct

																			4						in. (102 mm) i
											42 in.


													)
						(1067							)
													A



																												10-1/2 in.

8 in.
8 in.																												(267 mm)
(203 mm)																												(267 mm)
(203 mm)													B




									Chimney Sections

											A																B
	Catalog #									in			mm											in					mm
	SL306					6							152				4-3/4											121
	SL312					12							305				10-3/4											273
	SL318					18							457				16-3/4											425
	SL324					24							610				22-3/4											578
	SL336					36							914				34-3/4											883

	SL348					48							1219				46-3/4											1187

A = Actual Length

B = Effective Length (length of

chimney part after it has

been snapped to another)

										Inside
20-3/4 in.										Diameter
20-3/4 in.										8 in.
(527 mm)									(203 mm)
4-3/4 in. (121 mm)										Outside
										Outside
										Diameter
										Diameter
Effective Height										10-1/2 in.
										(267 mm)

CAK4A Chimney Air Kit

SL3 Vent Stabilizer

Heat & Glo • RH-36/RH-42 • 4044-153 • Rev W • 11/08

47

Image 47

Contents Fire Risk Wood Burning FireplaceOperation Hot screen/mesh and glass doors will cause burnsNumber Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited WarrantyHeat & Glo RH-36/RH-42 4044-153 Rev W 11/08 Combustible Materials Listing and Code ApprovalsAppliance Certiﬁcation Non-Combustible MaterialsHot glass will cause burns Operating InstructionsYour Fireplace Firescreen Seasoned WoodStarting a Fire GrateClear Space Glass DoorsVented Gas Log Sets & Gas Log Lighters Optional ComponentsWood Fuel Creosote Formation and Need for Removal Maintainance and ServiceChimney Inspection/Cleaning Disposal of AshesFrequency As desired Glass CleaningCheck Firebox Refractory Inspect GrateStart Fire Problems Possible Cause Solution Troubleshooting GuideGetting Started Installer GuideNegative Pressure Design and Installation ConsiderationsDraft Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyInspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Select Fireplace Location Mm all configurationsFraming & Clearances Clearances to Combustible Materials ClearancesModel # Opening Mensions Sidewalls/SurroundsFrame the Fireplace Outside DiPlace Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the FireplaceYES Ft min. from top of uppermost chimney section to air inletOutside Air Installation Install Outside Air KitMaintain minimum height of chimney above roof Chimney AssemblyHeight of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssemble Chimney Sections Install Chimney Air KitInstalling the Ceiling Firestop Install Ceiling FirestopsPrepare Attic Insulation Shield Install Attic Insulation ShieldCut out Hole in Roof Complete InstallationInstall Flashing Following steps should be skipped if using a chaseFlat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsCaulk all seams to prevent leaks Refer to Figure Install Fireplace & ChimneyInstall Chase Top Install as per Sections 7ST375 Square Termination Cap Install Termination CapTCT375 Terra Cotta Cap TS345/TS345P Square Termination CapOpen Top Shroud TR342 caps require radiation shield ShroudsRadiation Shield Field Constructed ShroudsRoofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield requiredRefer to .2 for hearth extension insulation alternatives FinishingHearth Extension = 1/k x inches of thicknessMinimum between Raised Hearth Extension FramingNoncombustible Finishing Materials Non-combustible SealantIn. Micore or equivilent insulation Finishing MaterialClearances to Mantels or other Combustibles above Fireplace Combustible MantelModel Outside Di- mensionsGas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provision Wood Burning InsertsModel # Fireplace DimensionsReference Materials Air Kit Parts 1321 mm 406 mm1676 mm 508 mm 13 mm ID4 Insulated Duct Mm i.d 1067 mm UD4 Uninsulated DuctCatalog # Chimney Components305 mm 24-5/8 625 mm 787 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm10-1/2 267 mm 305 mm 27-3/8 24-5/8 695 mm 625 mm10-7/8 276 mm Parts Service11/08 Heat & Glo RH-36/RH-42 4044-153 RevDo not Discard this Manual

RH-36 Series specifications

Hearth and Home Technologies has long been an industry leader in innovative heating solutions, and the RH-36 Series exemplifies this commitment to quality and performance. Designed to provide both comfort and efficiency, the RH-36 Series wood-burning fireplace inserts combine advanced technologies with timeless aesthetics, making them a popular choice among homeowners.

One of the standout features of the RH-36 Series is its impressive heat output. With a BTU rating that allows it to efficiently warm large spaces, this appliance is perfect for those chilly winter nights. The expansive firebox is designed to accommodate larger logs, thus extending burn times and reducing the frequency of refueling. This not only enhances convenience but also promotes a more sustainable approach to home heating.

The RH-36 Series also integrates the company’s patented Clean Burn Technology, which maximizes combustion efficiency. This system ensures that the wood is burned at optimal temperatures, resulting in less smoke and emissions. More so, this technology decreases creosote buildup within the chimney, enhancing safety and reducing the need for frequent maintenance.

In terms of aesthetics, the RH-36 Series doesn’t disappoint. Its large glass viewing area showcases the mesmerizing flames, creating a cozy atmosphere in any room. The fireplace insert is available in various finishes and door options, allowing homeowners to customize the look to suit their decor. Whether you prefer a traditional style or a modern finish, the RH-36 can fit seamlessly into your living space.

Furthermore, the RH-36 incorporates user-friendly features that enhance the overall experience. The easy-to-access ash pan allows for quick cleanup and maintenance, while the adjustable air control provides flexibility in regulating the burn rate, allowing users to create the desired ambiance with ease.

In conclusion, the Hearth and Home Technologies RH-36 Series is designed for those who value efficiency, safety, and aesthetic appeal in their heating solutions. With advanced technologies like Clean Burn, excellent heat output, customizable designs, and convenient features, this series stands as a pinnacle of wood-burning fire inserts, promising to deliver warmth and beauty to any home. Whether for cozy family gatherings or peaceful evenings, the RH-36 is a versatile choice that meets diverse heating needs while elevating home interiors.