Hearth and Home Technologies SL-550TV-IPI-E Appliance Preparation, Gas and Electrical Connections

Page 25

9 Appliance Preparation

A.Installing Outside Air Kit Damper Assem- bly

CAUTION! Risk of Cuts/Abrasions/Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp.

WARNING! Risk of Fire/Asphyxiation. DO NOT draw out-

side combustion air from:

•Wall, floor or ceiling cavity.

•Enclosed space such as an attic or garage.

•Close proximity to exhaust vents or chimneys. Fumes or odor may result.

•Remove and discard cover plate or knockout from side of appliance.

•Open air kit damper slightly.

•Locate door hinge toward back of appliance (see Figure 9.1).

DOOR

HINGE

HANDLE

Figure 9.1 Damper Assembly and Handle

•Attach damper assembly to appliance using screws provided (see Figure 9.2).

•Insert narrow end of handle through tab and into upper slot of door.

•Check handle operation. Pull handle out to open, and in to close.

Figure 9.2

Outside Air Kit Installation

B. Gas and Electrical Connections

If applicable, ensure that gas and electrical connections are installed at this time. Refer to Sections 11 (Gas Information) and 12 (Electrical Information).

C. Securing and Leveling the Appliance

WARNING! Risk of Fire! Prevent contact with:

•Sagging or loose insulation

•Insulation backing or plastic

•Framing and other combustible materials

Block openings into the chase to prevent entry of blown- in insulation. Make sure insulation and other materials are secured.

DO NOT notch the framing around the appliance standoffs.

Failure to maintain air space clearance may cause overheating and fire.

The diagram shows how to properly position, level, and se- cure the appliance (see Figure 9.11). Nailing tabs are pro- vided to secure the appliance to the framing members.

•Bend out nailing tabs on each side.

•Place the appliance into position.

•Keep nailing tabs flush with the framing.

•Level the appliance from side to side and front to back.

•Shim the appliance as necessary. It is acceptable to use wood shims underneath the appliance.

•Secure the appliance to the framing by using nails or screws through the nailing tabs.

•Secure the appliance to the floor by inserting two screws through the pilot holes at the bottom of the appliance.

NAILING TABS

BOTH SIDES

Figure 9.11 Proper Positioning, Leveling And Securing Of An Appliance

Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Hot glass will cause burns What to do if you smell gasHomeowner Reference Information CongratulationsUser Guide Table of ContentsTroubleshooting Appliance SetupReference Materials CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Appliance Certification Listing and Code ApprovalsTempered Glass Specifications BTU SpecificationsNon-Combustible Materials Specification High Altitude InstallationsCombustible Materials Specification Electrical CodesOperating Instructions User Guide Gas Fireplace SafetyYour Fireplace Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyFan Kit optional Decorative Doors and FrontsOn position. The ON/OFF switch may Turn off all electric power to the applianceLighting Instructions IPI Final inspection byAfter Fireplace is Lit Frequently Asked QuestionsMaintenance Tasks-Homeowner Maintenance and ServiceGlass Cleaning Remote ControlGasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualified Service TechnicianVenting LogsEither cobrahead or SIT Typical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Any such action may cause a fire hazardNegative Pressure Selecting Appliance Location Framing and ClearancesModel Minimum Clearances Constructing the Appliance ChaseModels Combustible Mantels Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsVent Guidelines Vent Information and DiagramsVent System Configuration Models Pipe SizePipe Clearances to Combustibles Vent Clearances and FramingWall and Ceiling Penetration Framing Vertical Penetration FramingAppliance Preparation Installing Outside Air Kit Damper Assem- blyGas and Electrical Connections Securing and Leveling the ApplianceAssembly of Vent Sections Installing Vent PipeInstall Attic Insulation Shield Securing Vent SectionsFuel Conversion Gas InformationGas Pressure Gas ConnectionOptional Accessories Requirements Wiring RequirementsElectrical Information Code CSA C22.1Ignition Module 3 VAC Transformer PLUG-IN Wall Switch Installation for Fan Optional Junction Box InstallationFinishing Dimensions of CombustiblesFacing Material Noncombustible Facing DiagramRemove Glass Assembly Appliance SetupClean the Appliance AccessoriesPlacing the Lava Rock Lava Rock, Mineral Wool/Ember PlacementInstall the Log Assembly PIN Hole Install Trim and/or Surround Install the MeshInstall Hood Air Shutter SettingSymptom Possible Cause Corrective Action TroubleshootingIntellifire Ignition System Ues to spark, and main Reference Materials Appliance Dimension DiagramService Parts Log Set AssemblyAt Depot Service Parts ListSL-750TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E Stocked SL-950TV-IPI-ESL-550 / 750 / 950TV-IPI-E Contact Information

SL-950TV-IPI-E, SL-550TV-IPI-E, SL-750TV-IPI-E specifications

Hearth and Home Technologies has long been a leader in the fireplace industry, renowned for blending innovation with functionality in their products. Among their impressive line-up, the SL-550TV-IPI-E, SL-750TV-IPI-E, and SL-950TV-IPI-E models stand out for their exceptional quality and advanced features, catering to various heating needs and aesthetic preferences.

The SL-550TV-IPI-E is designed for those wanting an efficient, stylish fireplace that fits seamlessly into modern living spaces. It offers a sleek design with expansive viewing areas, allowing for a captivating flame display. Its innovative IntelliFire Plus technology enhances convenience and efficiency by providing reliable, electronic ignition, which can be managed via a remote control. Noteworthy is the model's ability to operate with granular control, allowing users to adjust the flame height and heat output according to their needs.

Next, the SL-750TV-IPI-E steps up the game with its larger size and increased heating capacity. This model is perfect for medium to large rooms, providing excellent warmth while maintaining an elegant ambiance. Like the SL-550TV-IPI-E, it utilizes the IntelliFire Plus system for ease of use. In addition, it features a stunning firebox design that emphasizes authenticity with realistic logs and glowing embers, creating a true hearth experience. Its large viewing area enhances the visual impact, making it a focal point in any room.

Lastly, the SL-950TV-IPI-E is at the pinnacle of this series, offering the largest footprint and highest heating efficiency. Specifically designed for larger areas, this model not only delivers significant warmth but also serves as an impressive architectural feature. The SL-950TV-IPI-E integrates advanced heating technologies to maximize efficiency while minimizing fuel consumption. The remote control operation and customizable flame settings provide an exceptional level of convenience for homeowners.

All three models boast a range of customizable options, including finishes and surroundings, allowing them to fit a variety of decor styles. Their construction emphasizes quality, with durable materials designed to withstand the test of time. Furthermore, the sealed combustion system ensures safety and efficiency by drawing air from outside, reducing indoor air pollution.

In summary, the SL-550TV-IPI-E, SL-750TV-IPI-E, and SL-950TV-IPI-E models from Hearth and Home Technologies offer a harmonious blend of technology, aesthetics, and efficiency. Whether for ambiance or heating, these fireplaces provide a robust solution to enhance modern living spaces.
Top Page Image Contents