Hearth and Home Technologies SL-750TV-IPI-E, SL-550TV-IPI-E, SL-950TV-IPI-E Ues to spark, and main

Page 39

Intellifire Ignition System - (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

 

A. A shorted or loose connection in flame

Verify all connections to wiring diagram in manual. Verify

4. Pilot lights but contin-

sensing rod.

connections underneath pilot assembly are tight. Verify con-

ues to spark, and main

 

nections are not grounding out to metal chassis, pilot burn-

burner will not ignite.

 

er, pilot enclosure or screen if present, or any other metal

(If the pilot continues

 

object.

to spark after the

 

 

B. Poor flame rectification or contaminated

With fixed glass assembly in place, verify that flame is en-

pilot flame has been lit,

flame sensing rod.

gulfing flame sensing rod on left side of pilot hood. Flame

flame rectification has

 

sensing rod should glow shortly after ignition. Verify cor-

not occurred.)

 

 

rect pilot orifice is installed and gas inlet is set to pressure

 

 

 

 

specifications. Clean flame sensing rod with emery cloth to

 

 

remove any contaminants that may have accumulated on

 

 

flame sensing rod.

 

 

 

 

C. Module is not grounded.

Verify module is securely grounded to metal chassis of ap-

 

 

pliance. Verify that wire harness is firmly connected to the

 

 

module.

 

 

 

 

D. Damaged pilot assembly or contami-

Verify that ceramic insulator around the flame sensing rod

 

nated flame sensing rod.

is not cracked, damaged, or loose. Verify connection from

 

 

flame sensing rod to white sensor wire. Clean flame sensing

 

 

rod with emery cloth to remove any contaminants that may

 

 

have accumulated on flame sensing rod. Verify continuity

 

 

with a multimeter with ohms set at lowest range. Replace

 

 

pilot if any damage is detected.

 

 

 

 

E. Module.

Turn ON/OFF rocker switch or wall switch to OFF position.

 

 

Remove ignitor wire “I” from module. Place ON/OFF rocker

 

 

switch or wall switch in ON position. If there is no spark at “I”

 

 

terminal module must be replaced. If there is a spark at “I”

 

 

terminal, module is fine.

 

 

 

Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Hot glass will cause burns What to do if you smell gasHomeowner Reference Information CongratulationsUser Guide Table of ContentsAppliance Setup TroubleshootingReference Materials CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty BTU Specifications Listing and Code ApprovalsAppliance Certification Tempered Glass SpecificationsElectrical Codes High Altitude InstallationsNon-Combustible Materials Specification Combustible Materials SpecificationGas Fireplace Safety Operating Instructions User GuideYour Fireplace Decorative Doors and Fronts Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit optionalFinal inspection by Turn off all electric power to the applianceOn position. The ON/OFF switch may Lighting Instructions IPIAfter Fireplace is Lit Frequently Asked QuestionsRemote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningLogs Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection VentingEither cobrahead or SIT Typical Appliance System Getting StartedAny such action may cause a fire hazard Design and Installation ConsiderationsTools and Supplies Needed Inspect Appliance and ComponentsNegative Pressure Framing and Clearances Selecting Appliance LocationModel Minimum Constructing the Appliance Chase ClearancesModels Combustible Mantels Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsModels Pipe Size Vent Information and DiagramsVent Guidelines Vent System ConfigurationVertical Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Wall and Ceiling Penetration FramingSecuring and Leveling the Appliance Installing Outside Air Kit Damper Assem- blyAppliance Preparation Gas and Electrical ConnectionsSecuring Vent Sections Installing Vent PipeAssembly of Vent Sections Install Attic Insulation ShieldGas Connection Gas InformationFuel Conversion Gas PressureCode CSA C22.1 Wiring RequirementsOptional Accessories Requirements Electrical InformationIgnition Module 3 VAC Transformer PLUG-IN Wall Switch Installation for Fan Optional Junction Box InstallationFinishing Dimensions of CombustiblesFacing Material Noncombustible Facing DiagramAccessories Appliance SetupRemove Glass Assembly Clean the AppliancePlacing the Lava Rock Lava Rock, Mineral Wool/Ember PlacementInstall the Log Assembly PIN Hole Air Shutter Setting Install the MeshInstall Trim and/or Surround Install HoodTroubleshooting Symptom Possible Cause Corrective ActionIntellifire Ignition System Ues to spark, and main Reference Materials Appliance Dimension DiagramService Parts Log Set AssemblyAt Depot Service Parts ListSL-750TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E Stocked SL-950TV-IPI-ESL-550 / 750 / 950TV-IPI-E Contact Information

SL-950TV-IPI-E, SL-550TV-IPI-E, SL-750TV-IPI-E specifications

Hearth and Home Technologies has long been a leader in the fireplace industry, renowned for blending innovation with functionality in their products. Among their impressive line-up, the SL-550TV-IPI-E, SL-750TV-IPI-E, and SL-950TV-IPI-E models stand out for their exceptional quality and advanced features, catering to various heating needs and aesthetic preferences.

The SL-550TV-IPI-E is designed for those wanting an efficient, stylish fireplace that fits seamlessly into modern living spaces. It offers a sleek design with expansive viewing areas, allowing for a captivating flame display. Its innovative IntelliFire Plus technology enhances convenience and efficiency by providing reliable, electronic ignition, which can be managed via a remote control. Noteworthy is the model's ability to operate with granular control, allowing users to adjust the flame height and heat output according to their needs.

Next, the SL-750TV-IPI-E steps up the game with its larger size and increased heating capacity. This model is perfect for medium to large rooms, providing excellent warmth while maintaining an elegant ambiance. Like the SL-550TV-IPI-E, it utilizes the IntelliFire Plus system for ease of use. In addition, it features a stunning firebox design that emphasizes authenticity with realistic logs and glowing embers, creating a true hearth experience. Its large viewing area enhances the visual impact, making it a focal point in any room.

Lastly, the SL-950TV-IPI-E is at the pinnacle of this series, offering the largest footprint and highest heating efficiency. Specifically designed for larger areas, this model not only delivers significant warmth but also serves as an impressive architectural feature. The SL-950TV-IPI-E integrates advanced heating technologies to maximize efficiency while minimizing fuel consumption. The remote control operation and customizable flame settings provide an exceptional level of convenience for homeowners.

All three models boast a range of customizable options, including finishes and surroundings, allowing them to fit a variety of decor styles. Their construction emphasizes quality, with durable materials designed to withstand the test of time. Furthermore, the sealed combustion system ensures safety and efficiency by drawing air from outside, reducing indoor air pollution.

In summary, the SL-550TV-IPI-E, SL-750TV-IPI-E, and SL-950TV-IPI-E models from Hearth and Home Technologies offer a harmonious blend of technology, aesthetics, and efficiency. Whether for ambiance or heating, these fireplaces provide a robust solution to enhance modern living spaces.
Top Page Image Contents