Hearth and Home Technologies SL-750TV-IPI-E, SL-550TV-IPI-E owner manual Junction Box Installation

Page 30

E. Junction Box Installation

If the box is being wired from the INSIDE of the appli- ance:

•Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to dis- engage it from the outer shell (see Figure 12.4).

•Pull the electrical wires from outside the appliance through the opening into the valve compartment and secure wires with a Romex connector. See Figure 12.4.

•Make all necessary wire connections to the junction box/receptacle and reattach the junction box/receptacle to the outer shell.

F. Wall Switch Installation for Fan (Optional)

If the box is being wired to a wall mounted switch for use with a fan (See Figure 12.5):

•The power supply for the appliance must be brought into a switch box.

•The power can then be supplied from the switch box to the appliance using a minimum of 14-3 with ground wire.

•At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown.

•At the appliance connect the black (hot), white (neutral) and green (ground) wires to the junction box as shown.

•Add a 1/4 in. insulated female connector to the red (switch leg) wire, route it through the knockout in the face of the junction box, and connect to the top fan switch connector (1/4 in. male) as shown.

 

 

 

Romex

 

 

 

Connector

 

 

 

14/2WG

 

 

 

Cover Plate

 

 

 

outside firebox

WHT

 

 

 

BLK

 

 

WHT

BLK

 

Copper

 

 

 

 

 

 

 

GRN wire

ground attached

 

 

to GRN screw with

 

 

inside box

 

 

GRN wire

 

 

 

 

 

NOTICE: DO NOT wire

 

 

110 VAC to wall switch.

Figure 12.4 Junction Box Detail

 

Minimum 14-3 AWG

 

Switch

 

 

with Ground

 

 

 

Red

 

 

Black

Black

 

White

White

Junction Box

Green

Green

Red Black White Green

 

Power

 

Switch Box

 

Supply

 

 

 

 

Wires

 

Knockout

 

Red

 

 

Figure 12.5 Junction Box Wired to Wall Switch or BC10

30

Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08

Page 29 Page 31
Image 30
Page 29 Page 31
Contents What to do if you smell gas Hot glass will cause burnsCongratulations Homeowner Reference InformationTable of Contents User GuideAppliance Setup TroubleshootingReference Materials CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Tempered Glass Specifications Listing and Code ApprovalsAppliance Certification BTU SpecificationsCombustible Materials Specification High Altitude InstallationsNon-Combustible Materials Specification Electrical CodesGas Fireplace Safety Operating Instructions User GuideYour Fireplace Fan Kit optional Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Decorative Doors and FrontsLighting Instructions IPI Turn off all electric power to the applianceOn position. The ON/OFF switch may Final inspection byFrequently Asked Questions After Fireplace is LitGlass Cleaning Maintenance and ServiceMaintenance Tasks-Homeowner Remote ControlVenting Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection LogsEither cobrahead or SIT Getting Started Typical Appliance SystemInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Any such action may cause a fire hazardNegative Pressure Framing and Clearances Selecting Appliance LocationModel Minimum Constructing the Appliance Chase ClearancesModels Mantel and Wall Projections Combustible MantelsTermination Locations Vent Termination Minimum ClearancesVent System Configuration Vent Information and DiagramsVent Guidelines Models Pipe SizeWall and Ceiling Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Vertical Penetration FramingGas and Electrical Connections Installing Outside Air Kit Damper Assem- blyAppliance Preparation Securing and Leveling the ApplianceInstall Attic Insulation Shield Installing Vent PipeAssembly of Vent Sections Securing Vent SectionsGas Pressure Gas InformationFuel Conversion Gas ConnectionElectrical Information Wiring RequirementsOptional Accessories Requirements Code CSA C22.1Ignition Module 3 VAC Transformer PLUG-IN Junction Box Installation Wall Switch Installation for Fan OptionalDimensions of Combustibles FinishingNoncombustible Facing Diagram Facing MaterialClean the Appliance Appliance SetupRemove Glass Assembly AccessoriesLava Rock, Mineral Wool/Ember Placement Placing the Lava RockInstall the Log Assembly PIN Hole Install Hood Install the MeshInstall Trim and/or Surround Air Shutter SettingTroubleshooting Symptom Possible Cause Corrective ActionIntellifire Ignition System Ues to spark, and main Appliance Dimension Diagram Reference MaterialsLog Set Assembly Service PartsService Parts List At DepotSL-750TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E SL-950TV-IPI-E StockedSL-550 / 750 / 950TV-IPI-E Contact Information

SL-950TV-IPI-E, SL-550TV-IPI-E, SL-750TV-IPI-E specifications

Hearth and Home Technologies has long been a leader in the fireplace industry, renowned for blending innovation with functionality in their products. Among their impressive line-up, the SL-550TV-IPI-E, SL-750TV-IPI-E, and SL-950TV-IPI-E models stand out for their exceptional quality and advanced features, catering to various heating needs and aesthetic preferences.

The SL-550TV-IPI-E is designed for those wanting an efficient, stylish fireplace that fits seamlessly into modern living spaces. It offers a sleek design with expansive viewing areas, allowing for a captivating flame display. Its innovative IntelliFire Plus technology enhances convenience and efficiency by providing reliable, electronic ignition, which can be managed via a remote control. Noteworthy is the model's ability to operate with granular control, allowing users to adjust the flame height and heat output according to their needs.

Next, the SL-750TV-IPI-E steps up the game with its larger size and increased heating capacity. This model is perfect for medium to large rooms, providing excellent warmth while maintaining an elegant ambiance. Like the SL-550TV-IPI-E, it utilizes the IntelliFire Plus system for ease of use. In addition, it features a stunning firebox design that emphasizes authenticity with realistic logs and glowing embers, creating a true hearth experience. Its large viewing area enhances the visual impact, making it a focal point in any room.

Lastly, the SL-950TV-IPI-E is at the pinnacle of this series, offering the largest footprint and highest heating efficiency. Specifically designed for larger areas, this model not only delivers significant warmth but also serves as an impressive architectural feature. The SL-950TV-IPI-E integrates advanced heating technologies to maximize efficiency while minimizing fuel consumption. The remote control operation and customizable flame settings provide an exceptional level of convenience for homeowners.

All three models boast a range of customizable options, including finishes and surroundings, allowing them to fit a variety of decor styles. Their construction emphasizes quality, with durable materials designed to withstand the test of time. Furthermore, the sealed combustion system ensures safety and efficiency by drawing air from outside, reducing indoor air pollution.

In summary, the SL-550TV-IPI-E, SL-750TV-IPI-E, and SL-950TV-IPI-E models from Hearth and Home Technologies offer a harmonious blend of technology, aesthetics, and efficiency. Whether for ambiance or heating, these fireplaces provide a robust solution to enhance modern living spaces.
Top Page Image Contents