Hearth and Home Technologies ST42A Tools and Supplies Needed, Inspect Fireplace and Components

Page 8

D. Tools and Supplies Needed

Before beginning the installation be sure the following tools and building supplies are available:

Reciprocating saw	Framing material
Pliers	High temp caulking material
Hammer	Gloves
Phillips screwdriver	Framing square
Flat blade screwdriver	Electric drill and bits
Plumb line	Safety glasses
Level	Tape measure

1/2-3/4 in. length, #6 or #8 self-drilling screws

Misc. screws and nails

CAUTION

•Keep ﬁ replace dry.

•Mold or rust may cause odors.

E. Inspect Fireplace and Components

WARNING

Fire Risk

Explosion Risk

Inspect fireplace and components for damage. Damaged parts may impair safe operation.

•Do NOT install damaged components.

•Do NOT install incomplete components.

•Do NOT install substitute components Report damaged parts to dealer.

•Carefully remove the ﬁ replace and components from the packaging.

•The vent system components and doors are shipped in separate packages.

•Report to your dealer any parts damaged in shipment.

•Read all the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and beneﬁt.

8	Heatilator • ST42A • 35038 Rev G • 02/05

Image 8

Contents

ST42A Fire RiskHomeowner Reference Information Listing Label Information/LocationGrate NumberTable of Contents Not intended for use as a primary heat source Listing and Code Approvals Appliance Certiﬁcation Design and Installation Considerations Getting StartedNegative Pressure Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemFire Risk Explosion Risk Tools and Supplies NeededInspect Fireplace and Components Framing and Clearances Selecting Fireplace LocationClearances Mm minSidewalls/Surrounds Frame the FireplaceConstruct the Chase Chimney RequirementsInstallation of Fireplace Install the Outside Air KitSharp Edges Fire Risk Asphyxiation Risk Risk of Smoke SpillageSecure the Fireplace Position the FireplacePlace the Protective Metal Hearth Strips Level the FireplaceChimney Assembly C,f Using Offsets/Returns SL1106 SL1112 SL1118 SL1136 SL1148Install the Firestop Spacers Assemble the Chimney SectionsSecure the Chimney Install the Attic Insulation ShieldDouble-check the Chimney Assembly Complete the Enclosure Chimney TerminationInstall the Chimney Air Kit required in Canada Chase TopInstall the Termination Cap Installing an ST1175 Square Termination CapGas Code, Ansi Z223.1-1980 AccessoriesGas Log/Lighter Provisions Hearth Extension Insulation Alternatives, R Value = FinishingHearth Extension Mantel Finishing MaterialGlass Doors Operating Instructions General InformationOutside Air FirescreenClear Space Near the Fireplace Flue DamperGrate Wood FuelFirewood MoistureStarting a Fire Troubleshooting Understanding Vent ProblemsDiagnostics and Problem Solving Diagnostic QuestionsSolutions Can’t get a good ﬁre going. What am I doing wrong?ﬁreplace burns the wood too fast. What can I do? Maintenance and Servicing the Fireplace Chimney Inspection/CleaningDisposal of Ashes Firebox RefractoryMaintenance Task List When cleaning glass doorClean Chimney FireFireplace Dimensions Reference MaterialsFireplace Components Model # DescriptionChimney Components Catalog #15-1/4 387 mm 25-1/4 641 mm 14-3/4 375 mm TR442 TR442 / 444 TV Woodburning Termination CapShroud TS345 TR342 TR342 / 344 TV TR11 / 11T TR11 / 11T TV Service Parts ST42# Description of Part QtyLimited Warranty Contact Information