Baxi Potterton 24/1.0 Setting the Central Heating Times, Programming the Central Heating Times

Page 7

04. November

2008

08:50

Tuesday

 

 

Menu Button

Dial Knob

Display Screen

5.0Setting the Central Heating Times

5.1Programming the Central Heating Times

The programmar enables control of up to three periods a day, seven days a week.

There are 3 time programs preinstalled to aid reprogramming:- Time program 1 is the default with 3 time periods - Mon-Sun, 6-9, 11-12 and 15-22.

Time program 2 has two time switch periods - Mon-Sun, 6-9 and 15-22.

Time program 3 has one time switch period 6-22.

‘Preselection’ regimes are: Mon-Sun (Default) Mon-Fri and Sat-Sun or each day individually.

If there are two heating circuits with two PRU’s each room/floor must be programmed using the respective PRU. Choose the relevant heating circuit at STEP 3.

When programming individual days, the opportunity to copy one day to another is offered (screen 529). Lastly screen 536 enables a reset to the default values as given above.

STEP 1

STEP 2

The basic display is shown. If the basic display is not showing, press the MENU

button. until the basic display is shown

Press the MENU button.

04. November 2008

08:50---------------------------------------------------

Tuesday

Information

Set time and date

STEP 3

STEP 4

Turn the Dial Knob clockwise to

 

 

highlight ‘Time central heating

 

 

CH1’.

 

 

 

Operator section

 

 

Time central heating

CH1

 

Time hot water

 

Press the Dial Knob and the

STEP 5

 

 

 

day / days regime flashes.

 

 

Turn Dial to the required day

 

 

or days Mon-Sun, Mon-Fri,

 

 

Sat-Sun

 

 

Mon, Tue, Wed,

Time cental heating CH1

Select days

Mon - Sun

Thu, Fri, Sat, Sun

 

 

 

Press Dial to

 

 

select.

 

 

Press the Dial Knob to select .

Turn the Dial Knob one click clockwise.

Time

central heating

CH1

 

Select days

Mon - Sun

 

 

STEP 6

Time

central heating

CH1

 

Mon - Sun

 

Select default timings?

 

Press the Dial Knob and the time program regime flashes. Turn Dial to the ‘Time setting 1’. Press Dial to select and the screen goes back to STEP 6.

STEP 7

Time

central heating

CH1

 

Mon - Sun

 

Set to

Time setting 1

Turn the Dial Knob one click clockwise.

STEP 8

Time

central heating

CH1

Mon - Sun: 1st Time ON

 

 

06:00

© Baxi Heating UK Ltd 2010

7

Image 7
Contents Ecogen 24/1.0 0086 ContentsQuick Reference Guide Default 6am 9am, 11am 12pm & 15pm 22pmEasy menu button POU IntroductionDescription Important NotesPOU as a Programmable Room Unit PRU ProgrammersGetting Started Programmable Operator Unit POUTime Setting Setting the TimeStep Press the Dial Knob Setting the Central Heating TimesProgramming the Central Heating Times Highlight ‘Time central heating CH1’Required time. Press Display Screen Turn the Dial Knob one clickDial to select Programming the Domestic Hot Water Times Setting the DHW TimesTurn the Dial Knob clockwise To highlight ‘Time hot water’ Dial Knob. The ‘1st Time OFF’ Time will flash. Turn the Dial Menu Button Easy Menu Dial KnobSelecting the Cental Heating Mode Mode Selection/Temp AdjustmentFurther Information Room Temperature Setpoint Selecting the Domestic Hot Water DHW modeAdjusting the Room temperature set point Adjusting the DHW Tank TemperatureProgramme Lock Holiday modeContents of Other Functions Selecting Diagnostics engine Selecting Temps / mode CH1Selecting Temps / mode hot water Service/Special operationService reset Resetting the BoilerAutomatic reset User resetTop 200mm Bottom Left side 5mm Right Side 60mm Front Clearances5mm In Operation AR+ Error CodesList of Error Codes NRPEngine head control temperature less than 150 degrees C when Care of the Boiler Protection & PrecautionFault Indication Call your Installer or Service Engineer as soon as possibleContact the Electricity Provider Installation, Commissioning, Service & RepairBenchmark Commissioning Checklist LegislationPage Page Baxi Serial Number Date of InstallationBrooks House, Coventry Road, Warwick. CV34 4LL