LG Electronics LP091HEM-Y8 manual Architecture Grille Aluminum Single Pack, Architectural Grille

Page 28

Architecture Grille Aluminum - Single

Note:

Pack

A baffle kit must not be used with a stamped aluminum grille

Part No: AYAGALA01

on any PTAC installation.

 

Stamped Aluminum Grille

Stamped Aluminum Grille

Architecture Grille

Description

Outdoor grilles are attached to the wall sleeve and exposed to the exterior wall. The grilles are an industry standard size of 42" x 16".

Receiving

Upon receipt of the product, inspect the shipping carton for signs of visible damage. Report any damage or shortage to the carrier and note it on the delivery receipt. The unit must be stored in its original shipping carton in a dry, secure place prior to its installation and use.

Installation

The installation and servicing of the equipment referred to in this booklet should be performed by qualified, experienced technicians.

WARNING

Hazardous Voltage!

Disconnect all electric power, including remote disconnects before servicing. Follow proper lockout/tagout procedures to ensure the power can not be inadvertently energized. Failure to disconnect power before servicing could result in death or serious injury.

Important Note:

The unit OFF switch does not disconnect all electrical power to this unit.

1.Prepare the wall sleeve for installation of the grille by removing the cardboard stiffener and rear enclosure panel from the sleeve. These items may be removed from inside of the building.

Note:

The sleeve stiffener must be taken out before the rear sleeve enclosure panel can be removed from the sleeve.

2. Prepare the stamped aluminum grille for installation on the sleeve by inserting the six (6) plastic grommets into the square holes located near the outer edges of all four sides of the grille. With the grille positioned so the flanges of all four sides are in the up position, insert the grommets so the square end protrudes through the grille in the opposite direction from the flanges.

3.Turn the grille so it can be removed through the rear sleeve opening.

4.Install the stamped aluminum grille by aligning the guide pins located in the lower right and left hand corners of the grille with the corresponding holes in the rear of the wall sleeve.

5.Secure the grille by threading each of the screws into the plastic grommets.

6.Remove the wire handle (not shown in the picture) from the center of the grille prior to installing the chassis into the sleeve.

Note:

Be sure to keep a firm grip on wire handle and grille to prevent it from dropping and/or causing possible injury or property damage.

Architectural Grille

1.Remove the cardboard sleeve stiffener and the rear enclosure of the sleeve as described in Step 1 of the stamped aluminum grille instructions.

2.Turn the grille so it can be removed through the rear sleeve opening.

3.Install the grille by aligning the four screws supplied to their corresonding holes in the architectural grille.

Copyright ©2008 LG Electronics. Inc. All right reserved.

- 28 -

Only for training and service purposes

LGE Internal Use Only

 

Page 27 Page 29
Image 28
Page 27 Page 29
Contents SVC Manual Specification LGE Internal Use OnlyFeatures and Benefits Sleeve and the Rear GrilleDoor Switch/Occupancy Sensor Outdoor Air Temperature SwitchoverTemperature limits Quick Heater RecoveryOperation Electric Heating Model Control LocationsVentilation Temperature Limiting Additional ControlsRemoving the Front Grille Additional ControlsMolex Housing Spec REMOTE/LOCAL ControlEnergy Saver Front Desk ControlMechanical Parts Disassembly InstructionsFront Grille Control BOX AIR Handling Parts Electric Heater Electric Heater Model onlyCross Flow FAN Axial FANElectrical Parts ShroudOutdoor Motor CompressorPower Cord 6 P.C.BRefrigeration Cycle CondenserEvaporator Capillary TubeLGE Internal Use Only Pulling Vacuum Installation HOW to Install the UnitDimension of air conditioner Dimension of sleeve assembly optionalWall Case Installation Data Wall Sleeve InstallationGeneral Installation of Wall Case in Wall Opening As shipped, the LG wall sleeve is ready for installationPreparation of the Front Grille Preparation of the Wall Case for All Types of ConstructionLGE Internal Use Only Sub-Base Connected Unit Installation Electrical Safety Electrical RequirementsElectrical Data for 230/208V Model 208, 230, and 208/230 Volt UnitsField Installed Accessories InstallationControl Panel Key Lock DescriptionPart No AYSB2101 Condensate Disposal Pump Kit InstallationHazardous Voltage Place the top cover assembly back into the unit Spraying Architecture Grille Aluminum Single Pack Architectural GrilleCondensate Drain kit Drain InstallationPart No AYDR101 Outdoor Drain Kit Installation Outdoor Drain Kit InstallationIndoor Drain Kit Installation ChecklistLeveling Legs Part No AYLL101Leveling Leg Assembly Leveling Leg Assembly Installation on Wall SleeveHard Wire Kit Junction Box Kit Installation and Wiring ProcedurePart No AYAGALA01 Use Copper Conductors Only208/230 Volt Units Volt UnitsRemote Escutcheon Kit Part No AYRE110Subbase Part No AYSB1101 230/208V 20A AYSB2101 230/208V 30AAfter wiring is complete, mount covers a and F to To each installation instruction for that accessorySkirting Hole Location Right Cover Assembly Subbase with provided screws. FigureTroubleshooting Guide Outside DimensionsPiping System 066mm 406mm 505mmTroubleshooting Guide Fails to Start Complaint Cause Remedy Room AIR Conditioner Voltage Limits 208/230V 187V 253VComplaint Cause Remedy Piping Diagrams Th2 Thermistor for Evaporator pipe temperatureTh3 Thermistor for outdoor Air temperature Th4 Thermistor for Condenser pipe Air temperatureSchematic Diagram CN-NNExploded View 435300BJanuary

LP091HEM-Y8 specifications

The LG Electronics LP091HEM-Y8 is a versatile portable air conditioner designed to provide efficient cooling solutions for various environments. Compact yet powerful, this model is especially favored for its performance, ease of use, and innovative features that cater to the modern consumer's needs.

One of the standout characteristics of the LP091HEM-Y8 is its cooling capacity, rated at 9,000 BTU. This makes it ideal for rooms up to 400 square feet, allowing for effective temperature control in bedrooms, living rooms, or even small offices. The unit not only cools, but it also dehumidifies, helping to maintain a comfortable indoor air quality by removing excess moisture, which can be particularly beneficial in humid climates.

The unit operates on a convenient set of features, including a programmable timer that enables users to set the air conditioner to turn on or off at specific times, promoting energy efficiency and ensuring a comfortable environment whenever needed. The user-friendly control panel and included remote control facilitate easy temperature adjustments from across the room. Additionally, the LP091HEM-Y8 features multiple fan speeds and cooling modes, allowing for a customizable cooling experience.

In terms of technology, the LG LP091HEM-Y8 employs a dual inverter compressor. This technology enhances energy efficiency, significantly reducing electricity bills compared to traditional portable air conditioners while delivering rapid cooling performance. Its low noise operation provides a quiet environment, making it suitable for use in bedrooms or quiet working spaces.

Moreover, the LP091HEM-Y8 is designed with convenience in mind. It features a washable and reusable air filter, promoting cleaner air circulation while reducing maintenance costs. The unit's portable design, complete with caster wheels, makes it easy to move from room to room, and the simple installation process eliminates the need for complicated setups.

Finally, the sleek and modern design of the LP091HEM-Y8 seamlessly blends into various interior styles, making it a great addition to any home or office. With a combination of efficiency, ease of use, and advanced technology, the LG Electronics LP091HEM-Y8 continues to be a preferred choice for those seeking a reliable and effective air conditioning solution.
Top Page Image Contents