LG Electronics LP091HEM-Y8 manual Outdoor Drain Kit Installation

Page 30

Figure 42 – Outdoor Drain Kit Installation

DRAIN FITTING

 

BLANK-OFF

PLATE B

 

PLATE C

1/2" DRAIN

FITTING

GASKETS A

MTG. SCREWS

Outdoor Drain Kit Installation

Before installing the wall sleeve louvered condenser grille, it must be determined if the optional outdoor wall sleeve drain kit is to be installed. The drain kit will allow the condensate from the outdoor and indoor coils to be routed to a suitable area. The drain kit can be installed so the condensate can be drained from the right or left hand side of the wall sleeve. See Figure 42. See local codes for proper condensate disposal.

To install the outdoor drain components proceed as follows:

1.Remove the rear enclosure panel and the sleeve stiffener. These items may be removed from the inside of the building.

2.The drain fitting can be installed on the left or right hand side of the sleeve. (Illustration will be for a right hand installation.) Insert the drain fitting in the opening of gasket A and hole of plate B. Secure this assembly to the rear of the sleeve with two sheet metal screws into holes G provided in sleeve. See Figures 43 and 44.

3.Locate the other gasket A on the back of blank off plate C and secure the assembly to the left rear of wall sleeve with sheet metal screws provided. See Figure 45 for finished left hand side installation.

If the unit chassis is to be installed right away, install the condenser grille to wall sleeve with hardware provided. See condenser grille installation instructions.

If the unit chassis will not be installed right away, replace the rear enclosure panel in the wall sleeve. This will help protect the inside of the building from weather damage.

If a subbase is used, be sure the right hand subbase cover is removed before the chassis is installed in the sleeve. Slide the chassis into the wall sleeve until the chassis flanges

contact the front edge of sleeve. Secure the chassis to the wall sleeve on each side with screws provided.

Re-install the cabinet front.

See the following pages for installation instructions of indoor drain kit.

Figure 43

Figure 44

PLATE "B"

G

DRAIN FITTING

Figure 45

BLANK-OFF PLATE

SHEET METAL SCREWS

Figure 46

See Detail A

Sleeve overflow port

Do not close up this port

Gasket (2)

Blank-off Plate (2)

(4) Mounting Screws

Gasket

Wall Sleeve Bottom

 

Cover

 

Plate

 

1/2" Outdoor Drain Fitting

MTG. Screws (2)

Detail A

Copyright ©2008 LG Electronics. Inc. All right reserved.

- 30 -

Only for training and service purposes

LGE Internal Use Only

 

Page 29 Page 31
Image 30
Page 29 Page 31
Contents SVC Manual Specification LGE Internal Use OnlyFeatures and Benefits Sleeve and the Rear GrilleTemperature limits Door Switch/Occupancy SensorOutdoor Air Temperature Switchover Quick Heater RecoveryControl Locations Operation Electric Heating ModelVentilation Removing the Front Grille Temperature LimitingAdditional Controls Additional ControlsEnergy Saver Molex Housing SpecREMOTE/LOCAL Control Front Desk ControlDisassembly Instructions Mechanical PartsFront Grille Control BOX AIR Handling Parts Electric Heater Electric Heater Model onlyCross Flow FAN Axial FANOutdoor Motor Electrical PartsShroud CompressorPower Cord 6 P.C.BEvaporator Refrigeration CycleCondenser Capillary TubeLGE Internal Use Only Pulling Vacuum Dimension of air conditioner InstallationHOW to Install the Unit Dimension of sleeve assembly optionalWall Sleeve Installation Wall Case Installation DataGeneral Preparation of the Front Grille Installation of Wall Case in Wall OpeningAs shipped, the LG wall sleeve is ready for installation Preparation of the Wall Case for All Types of ConstructionLGE Internal Use Only Sub-Base Connected Unit Installation Electrical Data for 230/208V Model Electrical SafetyElectrical Requirements 208, 230, and 208/230 Volt UnitsControl Panel Key Lock Field Installed AccessoriesInstallation DescriptionCondensate Disposal Pump Kit Installation Part No AYSB2101Hazardous Voltage Place the top cover assembly back into the unit Spraying Architecture Grille Aluminum Single Pack Architectural GrilleDrain Installation Condensate Drain kitPart No AYDR101 Outdoor Drain Kit Installation Outdoor Drain Kit InstallationLeveling Legs Indoor Drain Kit InstallationChecklist Part No AYLL101Leveling Leg Assembly Leveling Leg Assembly Installation on Wall SleevePart No AYAGALA01 Hard Wire KitJunction Box Kit Installation and Wiring Procedure Use Copper Conductors Only208/230 Volt Units Volt UnitsRemote Escutcheon Kit Part No AYRE110Subbase Part No AYSB1101 230/208V 20A AYSB2101 230/208V 30ASkirting Hole Location Right Cover Assembly After wiring is complete, mount covers a and F toTo each installation instruction for that accessory Subbase with provided screws. FigurePiping System Troubleshooting GuideOutside Dimensions 066mm 406mm 505mmTroubleshooting Guide Fails to Start Complaint Cause Remedy Room AIR Conditioner Voltage Limits 208/230V 187V 253VComplaint Cause Remedy Th3 Thermistor for outdoor Air temperature Piping DiagramsTh2 Thermistor for Evaporator pipe temperature Th4 Thermistor for Condenser pipe Air temperatureSchematic Diagram CN-NNExploded View 435300BJanuary

LP091HEM-Y8 specifications

The LG Electronics LP091HEM-Y8 is a versatile portable air conditioner designed to provide efficient cooling solutions for various environments. Compact yet powerful, this model is especially favored for its performance, ease of use, and innovative features that cater to the modern consumer's needs.

One of the standout characteristics of the LP091HEM-Y8 is its cooling capacity, rated at 9,000 BTU. This makes it ideal for rooms up to 400 square feet, allowing for effective temperature control in bedrooms, living rooms, or even small offices. The unit not only cools, but it also dehumidifies, helping to maintain a comfortable indoor air quality by removing excess moisture, which can be particularly beneficial in humid climates.

The unit operates on a convenient set of features, including a programmable timer that enables users to set the air conditioner to turn on or off at specific times, promoting energy efficiency and ensuring a comfortable environment whenever needed. The user-friendly control panel and included remote control facilitate easy temperature adjustments from across the room. Additionally, the LP091HEM-Y8 features multiple fan speeds and cooling modes, allowing for a customizable cooling experience.

In terms of technology, the LG LP091HEM-Y8 employs a dual inverter compressor. This technology enhances energy efficiency, significantly reducing electricity bills compared to traditional portable air conditioners while delivering rapid cooling performance. Its low noise operation provides a quiet environment, making it suitable for use in bedrooms or quiet working spaces.

Moreover, the LP091HEM-Y8 is designed with convenience in mind. It features a washable and reusable air filter, promoting cleaner air circulation while reducing maintenance costs. The unit's portable design, complete with caster wheels, makes it easy to move from room to room, and the simple installation process eliminates the need for complicated setups.

Finally, the sleek and modern design of the LP091HEM-Y8 seamlessly blends into various interior styles, making it a great addition to any home or office. With a combination of efficiency, ease of use, and advanced technology, the LG Electronics LP091HEM-Y8 continues to be a preferred choice for those seeking a reliable and effective air conditioning solution.
Top Page Image Contents