State Industries 196114-000 instruction manual Table of Contents

Page 3

TABLE OF CONTENTS

 

 

Page

ROUGH-IN DIMENSIONS

2

FOREWORD

2

GENERAL SAFETY INFORMATION

3

Precautions

3

Liquid Petroleum

3

Chemical Vapor Corrosion

3

Improper Combustion

3

Extended Non-use Periods

3-4

Insulation Blankets

4

INSTALLATION INSTRUCTIONS

4

Required Ability

4

Locating The Heater

4

High Altitude Installations

4-5

Clearances

5

Hard Water

5

Air Requirements

5

Combination Water (Potable) Heating and Space Heating

5-6

Venting

6

Thermometers (Not Supplied)

6

Relief Valve

6-7

GENERAL SAFETY

 

INFORMATION

 

PRECAUTIONS

 

DO NOT USE THIS APPLIANCE IF ANY PART HAS BEEN UNDER WATER. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

IF THE UNIT IS EXPOSED TO THE FOLLOWING, DO NOT OPERATE HEATER UNTIL ALL CORRECTIVE STEPS HAVE BEEN MADE BY A QUALIFIED SERVICEMAN.

1.EXTERNAL FIRE.

2.DAMAGE.

3.FIRING WITHOUT WATER.

4.SOOTING

LIQUID PETROLEUM MODELS

WARNING

Water heaters for propane or liquified petroleum gas (LPG) are different from natural gas models. A natural gas heater will not function safely on LP gas and no attempt should be made to convert a heater from natural gas to LP gas.

 

Page

Gas Piping

7-8

Purging

8

Gas Pressure Regulation

9

OPERATION

9

Precautions

9

Lighting Instructions

10

Temperature Regulation

11

High Temperature Limit Switch

11

Checking Venting

11-12

SERVICE INFORMATION

12

Pilot and Main Burner

12

Checking Gas Input

12-13

Vent System

13

Relief Valve

13

Hot Water Odor

13

Anode Rod Inspection

13

Winter Protection

13

Replacement Parts

13

CHECKLIST

13-14

LIMITED WARRANTY

Insert

sodium chloride (water softener salt), waxes, and process chemicals are typical compounds which are potentially corrosive. Do not store products of this sort near the heater. Also, air which is brought in contact with the heater should not contain any of these chemicals. If necessary, uncontaminated air should be obtained from remote or outside sources. The limited warranty is voided when failure of the water heater is due to a corrosive atmosphere. (Refer to the limited warranty for complete terms and conditions.)

IMPROPER COMBUSTION

WARNING

ATTIC AND/OR EXHAUST FANS OPERATING ON THE PREMISES WITH A WATER HEATER CAN RESULT IN CARBON MONOXIDE POISONING AND DEATH.

OPERATION OF THESE FANS CAN PRODUCEANEGATIVE DRAFT IN THE AREA OF THE WATER HEATER PREVENTING THE PRODUCTS OF COMBUSTION FROM EXHAUSTING THROUGH THE CHIMNEY OR VENT PIPE.

The venting of the water heater should be inspected by a qualified service technician at the time of installation and periodically thereafter to ensure a down-draft condition does not exist.

DO NOT OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATING AIR. ADEQUATE AIR FOR COMBUSTION AND VENTILATION MUST BE PROVIDED FOR SAFE OPERATION.

CHEMICAL VAPOR CORROSION

WARNING

CORROSION OF THE FLUEWAYS AND VENT SYSTEM MAY OCCUR IF AIR FOR COMBUSTION CONTAINS CERTAIN CHEMICAL VAPORS. SUCH CORROSION MAY RESULT IN FAILURE AND RISK OF ASPHYXIATION.

Spray can propellants, cleaning solvents, refrigerator and air conditioning refrigerants, swimming pool chemicals, calcium and

EXTENDED NON-USE PERIODS

WARNING

HYDROGEN GAS CAN BE PRODUCED IN A HOT WATER SYSTEM SERVED BY THIS HEATER THAT HAS NOT BEEN USED FOR A LONG PERIOD OF TIME (GENERALLY TWO WEEKS OR MORE). HYDROGEN GAS IS EXTREMELY FLAMMABLE. To reduce the risk of injury under these conditions, it is recommended that the hot water faucet be opened for several minutes at the kitchen sink before using any electrical appliance connected to the hot water system. If hydrogen is present, there will probably be an unusual sound such as air escaping through the pipe as the water begins

3

Image 3
Contents Commercial GAS Water Heater Installation Operation Service Maintenance Limited WarrantyRecovery Capacities DimensionsTable of Contents Required Ability Installation InstructionsHigh Altitude Installations Insulation BlanketsCombination Water Potable Heating and Space Heating ClearancesHard Water AIR RequirementsDrafthood VentingRelief Valve System ConnectionsGAS Piping Single TemperaturePurging GAS Pressure RegulatorGAS Meter Size Natural GAS only Operation Manifold Pressure SettingFor Your Safety Read Before Lighting Temperature Regulation High Temperature Limit SwitchChecking Venting Pilot and Main Burner Service InformationPilot and Main Burner Checking GAS InputChecklist Water Heater Makes Sounds Water Temperature is TOO HOTGAS Smellat the Heater Water Leakage is Suspected

196114-000 specifications

State Industries 196114-000 is a prominent model in the realm of water heaters, designed to meet the diverse needs of modern households and commercial establishments. Renowned for its reliability and efficiency, this unit embodies advanced technologies that ensure optimal performance, durability, and energy savings.

One of the primary features of the 196114-000 is its high-capacity water tank, which is constructed from robust materials that resist corrosion and wear. This not only extends the lifespan of the unit but also ensures that hot water is readily available for various applications, whether it's for cooking, cleaning, or bathing. The tank's insulation aids in maintaining water temperature, reducing energy consumption and costs over time.

In terms of technology, the State Industries 196114-000 incorporates state-of-the-art heating elements that provide rapid heating of water. These elements are designed for efficiency, which translates into faster recovery rates and consistent water temperature. Additionally, the system employs smart control mechanisms that monitor water usage and adjust heating cycles accordingly, enhancing energy efficiency without compromising performance.

Safety features are another critical aspect of the 196114-000. It includes automatic shut-off functionalities, which protect against overheating and pressure build-up. This ensures not only the longevity of the unit but also safeguards users from potential hazards associated with malfunctioning water heaters.

The design of the 196114-000 is user-friendly, featuring an intuitive control panel that allows for easy temperature adjustments and monitoring. Maintenance is also simplified, with accessible components that make servicing straightforward and wear part replacement feasible without specialized tools.

Moreover, the compatibility of the State Industries 196114-000 with various installation configurations makes it a versatile choice for both residential and commercial applications. Its compact size allows for floor or wall mounting, catering to spaces with limited square footage.

In conclusion, the State Industries 196114-000 stands out in the competitive market of water heaters due to its blend of efficiency, safety, and advanced technology. Whether you're looking to upgrade your current system or install a new unit, this model promises reliable hot water supply and cost-effective operation, making it a trusted choice for countless users.