State Industries 184735-000 instruction manual Element Cleaning / Replacement

Page 15

4.Remove the two wires attached to the thermostat.

5.Remove the thermostat from behind the thermostat bracket.

6.Disconnect wires from thermostat and slide out of the bracket.

7.Place the new lower thermostat in the bracket making sure it fits firmly against the tank.

8.Attach the wires to the new thermostat.

NOTE: Some of the terminals may require straight-in wiring through an eye-opening. If wires are now looped, recut and strip wire 3/8” to a straight length and insert.

9.Put plastic terminal cover back in place.

10.Fold back the insulation to cover the thermostat.

11.Replace outer door then turn the electric power on.

ELEMENT CLEANING / REPLACEMENT

To remove the element from the tank in order to clean or replace it:

1.Before beginning turn “OFF” the electric power supply to the water heater.

2.Turn off the water supply to the water heater at the water shut-off valve or water meter.

The water passing out of the drain valve may be extremely hot. To avoid being scald, make sure all connections are tight and that the water flow is directed away from any person.

4. Remove the two screws securing the outer door, and remove door.

FIGURE 16.

5. Open the flap of insulation to expose the opening.

FIGURE 17.

6.Lift out the tab as shown below to unclip the terminal cover from the thermostat. The terminal cover can now be removed from the thermostat.

FIGURE 14.

3.Attach a hose to the water heater drain valve and put the other end in a floor drain or outdoors. Open the water heater drain valve. Open a nearby hot water faucet which will relieve pressure in the water heater and speed draining.

FIGURE 15.

FIGURE 18.

7.Disconnect the two wires on the element and unscrew the old element from the tank.

FIGURE 19.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Residential Point of USE Electric Important Definitions Safe INSTALLATION, USE and ServiceGeneral Safety Introduction Table of ContentsMixing Valve Usage Typical InstallationInsulation Blankets Installing the NEW Water HeaterLocating the NEW Water Heater Facts to Consider about the LocationWater Piping TEMPERATURE-PRESSURE Relief Valve Filling the Water Heater Optional Cord SET Wiring 120 Volt and 240 Volt Wiring DiagramsWiring Temperature Adjustment Temperature RegulationOperational Conditions For Your InformationDraining Periodic MaintenanceTEMPERATURE-PRESSURE Relief Valve Operation Thermostat Removal / ReplacementElement Cleaning / Replacement Service Drain Valve Washer ReplacementLeakage Checkpoints Problem Cause Solution Troubleshooting GuidelinesRepair Parts List Point of USE Electric ModelsDrain PAN

184735-000 specifications

State Industries is a prominent manufacturer known for its wide range of high-quality heating and cooling equipment, and the model number 184735-000 is a noteworthy example of its innovative product offerings. This particular model is designed to meet the demands of both residential and commercial settings, providing efficient solutions for temperature control.

One of the main features of the State Industries 184735-000 is its robust construction, ensuring durability and longevity even under the most demanding conditions. The unit is built with corrosion-resistant materials, making it a reliable choice for various environments, whether in humid coastal areas or dry inland regions. This factor significantly enhances its appeal to consumers who prioritize reliability in their heating and cooling systems.

In terms of technology, the 184735-000 incorporates advanced engineering principles that optimize energy efficiency. The unit is designed to adhere to modern energy standards and has potential for energy savings through its innovative compressor design. This technology not only reduces operational costs but also contributes to a reduced carbon footprint, making it an environmentally responsible choice.

The heating element in the State Industries 184735-000 utilizes state-of-the-art heating technology, providing rapid and efficient heating. This is particularly beneficial during colder months, ensuring that indoor spaces maintain a consistent and comfortable temperature. Additionally, it features user-friendly controls that allow for easy temperature adjustments, accommodating the varying preferences of different users.

Another characteristic worth mentioning is the unit's adaptability. The State Industries 184735-000 can be integrated with existing HVAC systems, enabling seamless installation and compatibility with current infrastructure. This aspect is crucial for both homeowners looking to upgrade their systems and businesses seeking to improve energy efficiency without a complete overhaul.

Furthermore, the model comes equipped with comprehensive safety features, including overheat protection and automatic shut-off mechanisms, ensuring safe operation even in the event of an unexpected malfunction. These features not only enhance user confidence but also contribute to the overall longevity of the unit.

In conclusion, the State Industries 184735-000 is designed with a focus on efficiency, durability, and user-friendliness. Its advanced technologies and robust construction make it a valuable asset for anyone seeking reliable heating and cooling solutions. Whether for residential or commercial use, this model stands out as a testament to State Industries' commitment to quality and innovation in the HVAC industry.
Top Page Image Contents