State Industries 184735-000 instruction manual Typical Installation, Mixing Valve Usage

Page 5

TYPICAL INSTALLATION

INSTALL SUITABLE DRAIN PANS

UNDER HEATERS TO PREVENT

DAMAGE DUE TO LEAKAGE.

REFER TO WATER HEATER

LOCATION ON PAGE 8.

INSTALL VACUUM RELIEF IN

COLD WATER INLET LINE AS

REQUIRED BY LOCAL CODES.

INSTALL THERMAL EXPANSION

TANK OR DEVICE IF WATER

HEATER IS INSTALLED IN A

CLOSED WATER SYSTEM.

FIGURE 1.

MIXING VALVE USAGE

Water (Potable) Heating: All models are considered suitable for water (potable) heating only.

HOTTER WATER CAN SCALD:

Water heaters are intended to produce hot water. Water heated to a temperature which will satisfy space heating, clothes washing, dish washing, and other sanitizing needs can scald and permanently injure you upon contact. Some people are more likely to be permanently injured by hot water than others. These include the elderly, children, the infirm, or physically/mentally handicapped. If anyone using hot water in your home fits into one of these groups or if there is a local code or state law requiring a certain temperature water at the hot water tap, then you must take special precautions. In addition to using the lowest possible temperature setting that satisfies your hot water needs, a means such as a *mixing valve, shall be used at the hot water taps used by these people or at the water heater. Mixing valves are available local plumbing

contractor. Consult a Qualified Installer or Service Agency. Follow mixing valve manufacturer’s instructions for installation of the valves. Before changing the factory setting on the thermostat, read the “Temperature Regulation” section in this manual.

FIGURE 2.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Residential Point of USE Electric Important Definitions Safe INSTALLATION, USE and ServiceGeneral Safety Introduction Table of ContentsMixing Valve Usage Typical InstallationLocating the NEW Water Heater Installing the NEW Water HeaterFacts to Consider about the Location Insulation BlanketsWater Piping TEMPERATURE-PRESSURE Relief Valve Filling the Water Heater Optional Cord SET Wiring 120 Volt and 240 Volt Wiring DiagramsWiring Temperature Adjustment Temperature RegulationOperational Conditions For Your InformationTEMPERATURE-PRESSURE Relief Valve Operation Periodic MaintenanceThermostat Removal / Replacement DrainingElement Cleaning / Replacement Service Drain Valve Washer ReplacementLeakage Checkpoints Problem Cause Solution Troubleshooting GuidelinesDrain PAN Repair Parts ListPoint of USE Electric Models

184735-000 specifications

State Industries is a prominent manufacturer known for its wide range of high-quality heating and cooling equipment, and the model number 184735-000 is a noteworthy example of its innovative product offerings. This particular model is designed to meet the demands of both residential and commercial settings, providing efficient solutions for temperature control.

One of the main features of the State Industries 184735-000 is its robust construction, ensuring durability and longevity even under the most demanding conditions. The unit is built with corrosion-resistant materials, making it a reliable choice for various environments, whether in humid coastal areas or dry inland regions. This factor significantly enhances its appeal to consumers who prioritize reliability in their heating and cooling systems.

In terms of technology, the 184735-000 incorporates advanced engineering principles that optimize energy efficiency. The unit is designed to adhere to modern energy standards and has potential for energy savings through its innovative compressor design. This technology not only reduces operational costs but also contributes to a reduced carbon footprint, making it an environmentally responsible choice.

The heating element in the State Industries 184735-000 utilizes state-of-the-art heating technology, providing rapid and efficient heating. This is particularly beneficial during colder months, ensuring that indoor spaces maintain a consistent and comfortable temperature. Additionally, it features user-friendly controls that allow for easy temperature adjustments, accommodating the varying preferences of different users.

Another characteristic worth mentioning is the unit's adaptability. The State Industries 184735-000 can be integrated with existing HVAC systems, enabling seamless installation and compatibility with current infrastructure. This aspect is crucial for both homeowners looking to upgrade their systems and businesses seeking to improve energy efficiency without a complete overhaul.

Furthermore, the model comes equipped with comprehensive safety features, including overheat protection and automatic shut-off mechanisms, ensuring safe operation even in the event of an unexpected malfunction. These features not only enhance user confidence but also contribute to the overall longevity of the unit.

In conclusion, the State Industries 184735-000 is designed with a focus on efficiency, durability, and user-friendliness. Its advanced technologies and robust construction make it a valuable asset for anyone seeking reliable heating and cooling solutions. Whether for residential or commercial use, this model stands out as a testament to State Industries' commitment to quality and innovation in the HVAC industry.
Top Page Image Contents