State Industries GPH-90N, 0710 316888-002 warranty Heat Cycle Definitions State Description

Page 37

HEAT CYCLE DEFINITIONS

STATE

DESCRIPTION

Pre-purge

If the heat engine initial call-for-heat is successful (all checks are passed), the combustion fan

 

is energized. The fan is started at a high speed for several seconds and the system verifies the

 

fan speed. Input signals (from other parts of the water heater) are verified before completion of

 

pre-purge including fan current verification. If one of the checks fails then the unit moves into

 

the post-purge mode followed by the hard lockout mode and the appropriate error is displayed

 

(see Error Code List and Clear-out Procedure).

Inter-Purge

If the flame presence is detected the control delays a pre-determined amount of time keeping

 

the spark igniter energized. If flame presence is not detected within 5 seconds from the

 

moment the gas was allowed in the combustion chamber (three ignition trials) then the control

 

will initiate an ignition re-try for two more times. If flame presence cannot be verified within

 

the given timing and after the ignitions’ re-try (if applicable), the system enters the post-purge

 

mode and the gas flow is turned off.

Post-Purge

The heat engine gas valve is now turned off and the fan speed is changed to high speed for

 

a predetermined time followed by a change of fan speed to a low value for the remaining

 

duration of the post purge mode. The control will also verify that the proper conditions are

 

maintained and there is no flame current sensed from the flame rod. If during the first stage

 

of the post-purge mode (high speed fan operation) conditions for a new call for heat are met

 

then the system will allow the state change to “Initial call for heat” only after the first stage of

 

the post-purge mode is complete.

Standby Mode

After successful completion of post-purge, the fan is turned off and the control will wait until

 

the determined conditions for a call for heat are met. In standby mode the unit continually

 

monitors the input and output conditions and if abnormal conditions are detected the unit will

 

enter in a lockout mode. If a call for heat is required and all checks are passed, the control

 

will return to the initial call for heat state.

Lockout mode

This is a non-operational mode following the detection of an error in the system. In this stage

 

the system displays an error message and continuously monitors input and output parameters.

 

The system can move from this state into the stand-by mode only if the error is cleared (typical

 

values for input and output parameters are recorded).

Proven Ignition

Once the power is turned on, the self-inspection is getting a normal status, water is turned

 

on and fan’s current is normal then the ignition process will start for 5 seconds. If ignition is

 

successful, the heater will go to normal combustion state and the ignition sparking will stop

 

after 3 seconds. If ignition fails, the control will attempt to cycle through the heating stage

 

three times and then attempt to re-ignite the gas. If ignition cannot be achieved, the control

 

will end ignition attempts and prevent any more heating cycles, close the gas valve, turn the

 

blower on, and display the E28 error message to the user.

 

TABLE 2

www.statewaterheaters.com

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents AN Odorant is Added to the GAS Used By this Water Heater Power Vent GAS ModelsTable of Contents Important Definitions Safe INSTALLATION, USE and ServiceGeneral Safety Can be triggered at any time Introduction Preparing for the InstallationPage GET to Know Your Water Heater GAS Models Replacement Parts and Deliming ProductsOperation Rough in Dimensions Installation ConsiderationsDirectly BELOW. Keep Clear of ALL Obstructions Suggested Piping Arrangement For TOP Connections Water Piping Mixing Valve UsageWater Potable Heating All models are considered Hotter Water can ScaldFacts to Consider about Location Handle Installation Earthquake Zones Page Appliances in Unconfined Spaces Combustion AIR and VentilationAppliances in Confined Spaces ALL AIR from Outdoors See Figures 12, 13 Water Piping Chemical Vapor CorrosionClosed Water Systems Thermal ExpansionHard Water TEMPERATURE-PRESSURE Relief ValveValve and Pipe Insulation if supplied GAS Piping GAS Line Purging High Altitude InstallationsFLOODING/FREEZING Filling the Water HeaterVent Pipe Termination If using 2 inch vent pipePlanning the Vent System If using 3 inch vent pipe Vent Terminal INSTALLATION, Sidewall Installation of Vent SystemCondensate Masonry Side WallsInstallation Sequence Sequence of InstallationsVent terminals supplied with heater must be used Installation of Vertical Vent System Installation of Vent SYSTEM, SidewallInitial Preparation Vent Pipe PreparationSelection of Materials Step a Recommended BRUSH* Size for Primer Cement ApplicationsStep B Step E Power VentStep F Step G Connection to Vent PipeVent Hoods MAY be Extremely HOT During Operation Filling the Water Heater Electrical ConnectionsCalibration Display Panel Operating InstructionsPage MCU Lighting Instructions For Your Safety Read Before LightingHeat Cycle Definitions State Description Temperature Regulation Temperature Probes Unique Hybrid FeaturesPage Temperature Regulation Start UP Conditions Constant Output Temperature ControlOperational Conditions Housekeeping MaintenanceVenting System Inspection Burner Operation and InspectionTEMPERATURE-PRESSURE Relief Valve Operation Anode ROD ReplacementCleaning the Inlet Water Filter MotorsFlushing the Heat Exchanger Lime BUILD- UP Cleaning the Heat EngineDraining the Tank Fault Indication and Error CodesRemarks Diagnostic DisplayCode Display Example Format Fault Lockout Code Description Cause Remedy Type Displayed Fault Lockout Code Description Cause Remedy Type Displayed Fault Lockout Code Description Cause Remedy Type Displayed Troubleshooting There is no HOT Water or When the TAP is OpenedHOT Water Turns Cold Stays ColdLeakage Checkpoints ServiceParts Identification Item # Description AB C DEF NIP/DIP/TBO/HT Replacement Parts DescriptionKIT # Claim Procedure Service and Labor ResponsibilityConditions and Exceptions Limitation on Implied WarrantiesPage

0710 316888-002, GPH-90N specifications

The State Industries GPH-90N,0710 316888-002 is a high-quality water heater designed to meet the demands of both residential and commercial applications. Renowned for its durability and efficiency, this model serves as an essential component for facilities requiring reliable hot water supply.

One of the standout features of the GPH-90N is its impressive heating capacity, which allows it to deliver hot water quickly and effectively. This model boasts a heating input of 90,000 BTU per hour, making it suitable for large households or commercial establishments. The unit is designed to maintain consistent water temperatures, ensuring that users have access to hot water whenever needed.

The GPH-90N is also equipped with advanced technologies that enhance its operational efficiency. It features a modulating gas burner that adjusts its output to match the flow rate of hot water demanded, thereby optimizing energy use and minimizing operating costs. This technology not only improves performance but also extends the lifespan of the water heater.

Durability is a key characteristic of the State Industries GPH-90N. The unit is crafted from high-quality materials, including a robust stainless steel tank that resists corrosion and ensures long-lasting performance. This corrosion-resistant design is particularly beneficial in areas with hard water, where mineral deposits can be a significant concern. Additionally, the tank is insulated with high-density foam, which helps to maintain heat and reduce standby heat loss.

A crucial aspect of the GPH-90N is its user-friendly features. The control panel is straightforward, allowing users to adjust settings with ease. The water heater is also designed for simple maintenance, ensuring that annual servicing can be carried out with minimal disruption.

Safety is paramount in the design of the GPH-90N. It includes multiple safety features, such as a pressure relief valve and a safety shut-off mechanism, which provide peace of mind for users. This ensures that the unit operates safely under varying conditions.

In conclusion, the State Industries GPH-90N,0710 316888-002 is a powerful and efficient water heater that combines advanced technology with durable construction. Its high heating capacity and user-friendly design make it a reliable choice for both residential and commercial applications, ensuring that hot water is always available when needed.
Top Page Image Contents