State Industries 0710 316888-002, GPH-90N warranty Vent Pipe Preparation, Initial Preparation

Page 28

FIGURE 28

VENT PIPE PREPARATION

1. INITIAL PREPARATION.

A. Make sure the solvent cement you are planning to

use is designed for the specific application you are

attempting.

B. Know the physical and chemical characteristics and

limitations of the PVC and CPVC piping materials

that you are about to use.

C. Know the reputation of your manufacturer and their

products.

D. Know your own qualifications or those of your

contractor. The solvent welding technique of joining

PVC and CPVC pipe is a specialized skill just as any

other pipe fitting technique.

E. Closely supervise the installation and inspect the

finished job before start-up.

F. Contact the manufacturer, supplier, or competent

consulting agency if you have any questions about

the application or installation of PVC and CPVC

pipe.

G. Take the time and effort to do a professional job.

Shortcuts will only cause you problems and delays

in start-up. By far, the majority of failures in PVC and

CPVC systems are the result of shortcuts and/or

improper joining techniques.

2. SELECTION OF MATERIALS.

• Cutting Device - Saw or Pipe Cutter.

3 in. (7.6cm)

MIN. LENGTH

A VENT USED IN A SPECIAL VENTING SYSTEM WITH POSITIVE VENT PRESSURE AND PASSING THROUGH A ROOF SHALL EXTEND AT LEAST 450mm (18 in.) ABOVE THE HIGHEST POINT WHERE IT PASSES THROUGH THE ROOF SURFACE AND ANY OTHER OBSTRUCTION WITHIN A HORIZONTAL DISTANCE OF 450mm (18 in.). A VERTICAL

VENTING SYSTEM MUST BE SUPPORTED EVERY 1.5m (5 ft.).

TERMINATION

MAY BE 45°

ELBOW OR A

“T” ELBOW

RODENT

18 in.SCREEN

(45cm) (INSTALL INTO

ELBOW)

ROOF

LINE

• Deburring Tool, Knife, File, or Beveling Machine (2

in. and above).

• Brush - Pure Bristle.

• Rag - Cotton (Not Synthetic).

• Primer and Cleaner.

• Solvent Cement - PVC for PVC Components and

CPVC for CPVC Components.

• Containers - Metal or Glass to hold Primer and

Cement. Select the type of PVC or CPVC materials

to be used on the basis of their application with

respect to chemical resistance, pressure rating,

temperature characteristics, etc.

• Insertion Tool - Helpful for larger diameter pipe and

fittings 6 in. (15cm) and above.

FIGURE 29

IMPORTANT

The vent system must terminate so that proper clearances are maintained as cited in local codes or the current edition of the National Fuel Gas Code (ANSI Z223.1) and as listed below:

1.Vent Termination must extend a minimum of 18 in. (46cm) above roof or 18 in. (46cm) above the anticipated snow level to prevent blockage of the vent termination, as shown in Figures 28 and 29.

28

www.statewaterheaters.com

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Power Vent GAS Models AN Odorant is Added to the GAS Used By this Water HeaterTable of Contents Safe INSTALLATION, USE and Service Important DefinitionsGeneral Safety Can be triggered at any time Preparing for the Installation IntroductionPage GET to Know Your Water Heater GAS Models Replacement Parts and Deliming ProductsOperation Installation Considerations Rough in DimensionsDirectly BELOW. Keep Clear of ALL Obstructions Water Piping Mixing Valve Usage Suggested Piping Arrangement For TOP ConnectionsWater Potable Heating All models are considered Hotter Water can ScaldFacts to Consider about Location Handle Installation Earthquake Zones Page Appliances in Unconfined Spaces Combustion AIR and VentilationAppliances in Confined Spaces ALL AIR from Outdoors See Figures 12, 13 Chemical Vapor Corrosion Water PipingClosed Water Systems Thermal ExpansionTEMPERATURE-PRESSURE Relief Valve Hard WaterValve and Pipe Insulation if supplied GAS Piping High Altitude Installations GAS Line PurgingFLOODING/FREEZING Filling the Water HeaterVent Pipe Termination If using 2 inch vent pipePlanning the Vent System If using 3 inch vent pipe Installation of Vent System Vent Terminal INSTALLATION, SidewallCondensate Masonry Side WallsInstallation Sequence Sequence of InstallationsVent terminals supplied with heater must be used Installation of Vent SYSTEM, Sidewall Installation of Vertical Vent SystemInitial Preparation Vent Pipe PreparationSelection of Materials Step a Recommended BRUSH* Size for Primer Cement ApplicationsStep B Power Vent Step EStep F Step G Connection to Vent PipeVent Hoods MAY be Extremely HOT During Operation Filling the Water Heater Electrical ConnectionsCalibration Operating Instructions Display PanelPage MCU For Your Safety Read Before Lighting Lighting InstructionsHeat Cycle Definitions State Description Temperature Regulation Unique Hybrid Features Temperature ProbesPage Temperature Regulation Start UP Conditions Constant Output Temperature ControlOperational Conditions Maintenance HousekeepingVenting System Inspection Burner Operation and InspectionAnode ROD Replacement TEMPERATURE-PRESSURE Relief Valve OperationCleaning the Inlet Water Filter MotorsCleaning the Heat Engine Flushing the Heat Exchanger Lime BUILD- UPFault Indication and Error Codes Draining the TankRemarks Diagnostic DisplayCode Display Example Format Fault Lockout Code Description Cause Remedy Type Displayed Fault Lockout Code Description Cause Remedy Type Displayed Fault Lockout Code Description Cause Remedy Type Displayed Troubleshooting When the TAP is Opened There is no HOT Water orHOT Water Turns Cold Stays ColdService Leakage CheckpointsParts Identification Item # Description AB C DEF NIP/DIP/TBO/HT Replacement Parts DescriptionKIT # Service and Labor Responsibility Claim ProcedureConditions and Exceptions Limitation on Implied WarrantiesPage

0710 316888-002, GPH-90N specifications

The State Industries GPH-90N,0710 316888-002 is a high-quality water heater designed to meet the demands of both residential and commercial applications. Renowned for its durability and efficiency, this model serves as an essential component for facilities requiring reliable hot water supply.

One of the standout features of the GPH-90N is its impressive heating capacity, which allows it to deliver hot water quickly and effectively. This model boasts a heating input of 90,000 BTU per hour, making it suitable for large households or commercial establishments. The unit is designed to maintain consistent water temperatures, ensuring that users have access to hot water whenever needed.

The GPH-90N is also equipped with advanced technologies that enhance its operational efficiency. It features a modulating gas burner that adjusts its output to match the flow rate of hot water demanded, thereby optimizing energy use and minimizing operating costs. This technology not only improves performance but also extends the lifespan of the water heater.

Durability is a key characteristic of the State Industries GPH-90N. The unit is crafted from high-quality materials, including a robust stainless steel tank that resists corrosion and ensures long-lasting performance. This corrosion-resistant design is particularly beneficial in areas with hard water, where mineral deposits can be a significant concern. Additionally, the tank is insulated with high-density foam, which helps to maintain heat and reduce standby heat loss.

A crucial aspect of the GPH-90N is its user-friendly features. The control panel is straightforward, allowing users to adjust settings with ease. The water heater is also designed for simple maintenance, ensuring that annual servicing can be carried out with minimal disruption.

Safety is paramount in the design of the GPH-90N. It includes multiple safety features, such as a pressure relief valve and a safety shut-off mechanism, which provide peace of mind for users. This ensures that the unit operates safely under varying conditions.

In conclusion, the State Industries GPH-90N,0710 316888-002 is a powerful and efficient water heater that combines advanced technology with durable construction. Its high heating capacity and user-friendly design make it a reliable choice for both residential and commercial applications, ensuring that hot water is always available when needed.
Top Page Image Contents