Leakage Checkpoints, Service | State Industries GS675YRVLT specs

Service

If a condition persists or you are uncertain about the operation of the water heater contact a service agency.

Use this guide to check a “Leaking” water heater. Many suspected “Leakers” are not leaking tanks. Often the source of the water can

be found and corrected.

If you are not thoroughly familiar with gas codes, your water heater, and safety practices, contact your gas supplier or qualified installer

to check the water heater.

Read this manual first. Then before checking the water heater make sure the gas supply has been turned “OFF”, and never turn the gas “ON” before the tank is completely full of water.

LEAKAGE CHECKPOINTS

Never use this water heater unless it is completely filled with water. To prevent damage to the tank, the tank must be filled with water.

BWater must flow from the hot water faucet before turning “ON” gas to the water heater.

	A	*Condensation may be seen on pipes in humid weather or pipe
D		connections may be leaking.
D
	B. *The anode rod fitting may be leaking.
C	C. Small amounts of water from temperature-pressure relief valve

		may be due to thermal expansion or high water pressure in your
		area.
	D. *The temperature-pressure relief valve may be leaking at the
		tank fitting.
	E. Water from a drain valve may be due to the valve being slightly
		opened.
	F. *The drain valve may be leaking at the tank fitting.
F	G. Combustion products contain water vapor which can condense
	G	on the cooler surfaces of the tank. Droplets form and drip onto
	G	the burner or run on the floor. This is common at the time of

E		start-up after installation and when incoming water is cold.
	H. Water in the water heater bottom or on the floor may be
		from condensation, loose connections, or the relief valve.
		DO NOT replace the water heater until a full inspection of
		all possible water sources is made and necessary corrective
		steps taken.
	Leakage from other appliances, water lines, or ground seepage
	should also be checked.
	*	To check where threaded portion enters tank, insert cotton
		swab between jacket opening and fitting. If cotton is wet, follow

“Draining” instructions in the “Periodic Maintenance” section and then remove fitting. Put pipe dope or teflon tape on the threads and replace. Then follow “Filling the Water Heater” instructions in the “Installing the New Water Heater” section.

GS675YRVLT specifications

The State Industries GS675YRVLT is a highly efficient and reliable water heater designed for residential use. It features advanced technologies and specifications that cater to the needs of modern households, making it an excellent choice for those seeking comfort and convenience in their hot water supply.

One of the standout features of the GS675YRVLT is its Energy Star certification, which signifies that it meets strict energy efficiency guidelines set by the U.S. Environmental Protection Agency. This certification not only ensures lower utility bills for homeowners but also contributes to reduced environmental impact, aligning with sustainable practices.

The unit is equipped with a powerful 67-gallon tank, providing ample hot water for larger families or households with high hot water demands. With its recovery rate, it can deliver consistent hot water, making it ideal for simultaneous use in multiple outlets, such as showers, dishwashers, and laundry machines.

A key characteristic of the GS675YRVLT is its durable construction. The tank is built with a glass lining that resists corrosion, extending the life of the water heater and minimizing the need for frequent replacements. Additionally, the reinforced insulation helps retain heat, improving the overall energy efficiency of the system.

The GS675YRVLT utilizes advanced heating technology. It features a high-efficiency gas burner that accelerates the heating process, ensuring quicker access to hot water. The combination of this burner and the unit's insulation means that users benefit from lower energy consumption without sacrificing performance.

Safety is also a priority in the design of this water heater. The GS675YRVLT includes a pressure relief valve, which prevents excessive pressure buildup, and it is equipped with a flame arrestor, minimizing the risk of combustion. These safety features are essential for ensuring peace of mind for homeowners.

User-friendly controls and a digital thermostat are other notable aspects of this unit. They allow for easy temperature adjustments and monitoring of energy usage.

In summary, the State Industries GS675YRVLT is a top-tier water heater that combines energy efficiency, robust construction, advanced technologies, and safety features. It is an ideal solution for those looking to enhance their home's hot water system while also being considerate of energy consumption and environmental responsibility.