Graco 220663, 220667, 220666, 237012, 237008, 237013, 237011, 220664, 237009 Skin Injection Hazard

Page 3

Warnings

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions.

WARNING

SKIN INJECTION HAZARD

Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury.

DFluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate surgical treatment.

DDo not point the gun at anyone or at any part of the body.

DDo not put your hand or fingers over the spray tip.

DDo not stop or deflect leaks with your hand, body, glove or rag.

DDo not “blow back” fluid; this is not an air spray system.

DAlways have the tip guard and the trigger guard on the gun when spraying.

DCheck the gun diffuser operation weekly. Refer to the gun manual.

DBe sure the gun trigger safety operates before spraying.

DLock the gun trigger safety when you stop spraying.

DFollow the Pressure Relief Procedure on page 10 whenever you: are instructed to relieve pres- sure; stop spraying; clean, check, or service the equipment; and install or clean the spray tip.

DTighten all fluid connections before operating the equipment.

DCheck the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. Perma- nently coupled hoses cannot be repaired; replace the entire hose.

DUse only Graco approved hoses. Do not remove the spring guard that is used to help protect the hose from rupture caused by kinks or bends near the couplings.

307843 3

Image 3
Contents Instructions-Parts List Series PumpsElectro-polished for use with waterborne coatings Table of Contents Skin Injection Hazard Equipment Misuse Hazard Fire and Explosion Hazard Installation Mounting the PumpGeneral Information Grounding Connect the Fluid Suction Line Connect the Fluid LinesVentilate the Air Exhaust Connect the Air LinesOperation Pressure Relief ProcedureStart and Adjust the Pump Applies only when using a spray gun or dispensing valvePressurized Equipment Hazard Symptom Probable Cause Test Procedure Remedy TroubleshootingTroubleshooting Tighten Threaded Connections MaintenanceCheck and Service the Lubricator, Regula- tor, and Filter Flush the Pump With Compatible SolventService Repairing the Ball Check ValvesRepairing the Fluid Piston and Seal Service 46 or Repairing the Air Motor and Piston 02327 Repairing the Air Control Valve 40c 40h 40f 40g 40b 40n Repairing the Pilot Valve 72 5h Parts For pump Model 237008 only For pump Model 220663 only52*51 7326 For pump Model 237011 only For pump Model 220666 onlyParts For pump Model 237009 only For pump Model 220664 only5026 For pump Model 237012 only For pump Model 220667 only02334 For pump Model 237010 only For pump Model 220665 only02335 For pump Model 237013 only For pump Model 220668 onlyRef No Air Control Valve Ref No Pilot Valve Repair and Conversion Kits 220948 SEAT, carbide 108822 Repair and Conversion Kits Filter, Regulator, Lubricator FRL Kit Filter, Regulator, Lubricator KitReturn Tube Drum Cover Kit and Return Tube KitDrum Cover Kit Return Tube KitSuction Kit Suction KitModel 220666 Technical Data, 400 Series PumpsPerformance Chart, 400 Series Pumps Model 220663Model 220667 Technical Data, 1200 Series PumpsPerformance Chart, 1200 Series Pumps Model 220664Model 220668 Technical Data, 2500 Series PumpsPerformance Chart, 2500 Series Pumps Model 220665Mounting Hole Layout Dimensional DrawingGraco Information Graco Standard Warranty