Graco 220663 Service, Repairing the Ball Check Valves, Repairing the Fluid Piston and Seal

Page 15

Service

Repairing the Ball Check Valves

NOTE: Parts marked with an asterisk are included in a repair kit, for example, (54*). See pages 38 and 39 for repair kit part numbers. Use all the parts in the kit for the best results.

Disassembly

1.Relieve the pressure.

WARNING

PRESSURIZED EQUIPMENT HAZARD

To reduce the risk of a serious injury whenever you are instructed to relieve pressure, follow the Pres- sure Relief Procedure on page 10.

2.Disconnect the air and fluid lines, remove the pump from its mounting, and place it on a bench.

3.Remove the cap (53) from each side of the outlet housing (33). See Fig. 6.

4.Remove the ball guide (56), ball (57), valve seat (49), and o-ring (48*) on each side of the outlet housing.

5.Inspect the ball stop (55) inside the cap (53) for wear. Remove o–ring (54). Replace if necessary.

6.Clean all parts and inspect for wear or damage. Replace as needed.

Assembly

1.Lubricate the o-rings (48*) and place one in the groove on each valve seat (49).

2.Install the valve seat (49) with the o-ring (48) fac- ing down, ball (57), and ball guide (56) into each outlet housing (33).

NOTE: Stainless steel seats are reversible.

3.Lubricate the o-rings (54*) and the cap (53) threads. Place one o-ring on each cap. Screw the caps into the housing and torque them to 55 to 85 ft-lb (75 to 115 NSm).

NOTE: On stainless steel pumps (Models 220666 through 220668 and Models 237011 to 237013), apply anti-seize lubricant to the threads of the cap (53).

Repairing the Fluid Piston and Seal

NOTE: Parts marked with an asterisk are included in a repair kit, for example, (52*). See pages 38 and 39 for repair kit part numbers. Use all the parts in the kit for the best results.

Disassembly

1.Relieve the pressure.

WARNING

PRESSURIZED EQUIPMENT HAZARD

To reduce the risk of a serious injury whenever you are instructed to relieve pressure, follow the Pres- sure Relief Procedure on page 10.

2.Loosen the tube nuts (A) and remove the outlet manifold (50). Unscrew the connectors (51). Re- move the o–ring (52). See Fig. 6.

3.Remove the screws (34), washers (35), outlet housing (33), piston seal (13*) and retaining plate (12). Remove the o–ring (18). Repeat on the other side of the pump.

4.Holding the screw (16) on one side of the pump, loosen the screw three or four turns on the oppo- site side of the pump, using a socket and breaker bar.

5.Remove the piston (17) by grasping it with your hand and and hit screw (16) with a plastic mallet to drive piston loose from shaft. Remove screw (16) and piston (17).

6.Remove the screws (32), washers (46 or 61), and inlet manifold (47). Remove o–rings (19).

7.Remove the intake housing (36), bellows (14*), and retaining plate (20).

8.Holding the piston shaft (15) flats with a wrench, remove the remaining screw (16).

9.Repeat steps 6 and 7 on the opposite end of the pump. Clean all parts and inspect for wear or dam- age. Replace as needed.

307843 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Instructions-Parts List Series PumpsElectro-polished for use with waterborne coatings Table of Contents Skin Injection Hazard Equipment Misuse Hazard Fire and Explosion Hazard Installation Mounting the PumpGeneral Information Grounding Connect the Fluid Suction Line Connect the Fluid LinesVentilate the Air Exhaust Connect the Air LinesOperation Pressure Relief ProcedureStart and Adjust the Pump Applies only when using a spray gun or dispensing valvePressurized Equipment Hazard Symptom Probable Cause Test Procedure Remedy TroubleshootingTroubleshooting Tighten Threaded Connections MaintenanceCheck and Service the Lubricator, Regula- tor, and Filter Flush the Pump With Compatible SolventService Repairing the Ball Check ValvesRepairing the Fluid Piston and Seal Service 46 or Repairing the Air Motor and Piston 02327 Repairing the Air Control Valve 40c 40h 40f 40g 40b 40n Repairing the Pilot Valve 72 5h Parts For pump Model 237008 only For pump Model 220663 only52*51 7326 For pump Model 237011 only For pump Model 220666 onlyParts For pump Model 237009 only For pump Model 220664 only5026 For pump Model 237012 only For pump Model 220667 only02334 For pump Model 237010 only For pump Model 220665 only02335 For pump Model 237013 only For pump Model 220668 onlyRef No Air Control Valve Ref No Pilot Valve Repair and Conversion Kits 220948 SEAT, carbide 108822 Repair and Conversion Kits Filter, Regulator, Lubricator FRL Kit Filter, Regulator, Lubricator KitReturn Tube Drum Cover Kit and Return Tube KitDrum Cover Kit Return Tube KitSuction Kit Suction KitModel 220666 Technical Data, 400 Series PumpsPerformance Chart, 400 Series Pumps Model 220663Model 220667 Technical Data, 1200 Series PumpsPerformance Chart, 1200 Series Pumps Model 220664Model 220668 Technical Data, 2500 Series PumpsPerformance Chart, 2500 Series Pumps Model 220665Mounting Hole Layout Dimensional DrawingGraco Information Graco Standard Warranty
Top Page Image Contents