Graco 237008, 220667, 220666, 237012, 220663, 237013, 237011, 220664, 237009 Equipment Misuse Hazard

Page 4

WARNING

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

INSTRUCTIONS

DThis equipment is for professional use only.

DRead all instruction manuals, tags, and labels before operating the equipment.

DUse the equipment only for its intended purpose. If you are uncertain about usage, call your Graco distributor.

DDo not alter or modify this equipment. Use only genuine Graco parts and accessories.

DCheck equipment daily. Repair or replace worn or damaged parts immediately.

DDo not exceed the maximum working pressure of the lowest rated system component. Refer to the Technical Data section on pages 44 through 46 for the maximum working pressure of this equip- ment.

DUse fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech- nical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

DDo not use hoses to pull equipment.

DRoute hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose Graco hoses to temperatures above 82_C (180_F) or below –40_C (–40_F).

DDo not lift pressurized equipment.

DComply with all applicable local, state, and national fire, electrical, and safety regulations.

DNever place your hands on or near the pump fluid inlet. Powerful suction could cause serious bodily injury.

MOVING PARTS HAZARD

Moving parts can pinch or amputate your fingers or other body parts.

DKeep clear of all moving parts when starting or operating the equipment.

DBefore servicing the equipment, follow the Pressure Relief Procedure on page 10 to prevent the equipment from starting unexpectedly.

DNever operate the motor with the pump housing removed.

4 307843

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Series Pumps Instructions-Parts ListElectro-polished for use with waterborne coatings Table of Contents Skin Injection Hazard Equipment Misuse Hazard Fire and Explosion Hazard Mounting the Pump InstallationGeneral Information Grounding Connect the Fluid Lines Connect the Fluid Suction LineConnect the Air Lines Ventilate the Air ExhaustPressure Relief Procedure Start and Adjust the PumpApplies only when using a spray gun or dispensing valve OperationPressurized Equipment Hazard Troubleshooting Symptom Probable Cause Test Procedure RemedyTroubleshooting Maintenance Check and Service the Lubricator, Regula- tor, and FilterFlush the Pump With Compatible Solvent Tighten Threaded ConnectionsRepairing the Ball Check Valves ServiceRepairing the Fluid Piston and Seal Service 46 or Repairing the Air Motor and Piston 02327 Repairing the Air Control Valve 40c 40h 40f 40g 40b 40n Repairing the Pilot Valve 72 5h Parts For pump Model 220663 only For pump Model 237008 only52*51 7326 For pump Model 220666 only For pump Model 237011 onlyParts For pump Model 220664 only For pump Model 237009 only5026 For pump Model 220667 only For pump Model 237012 only02334 For pump Model 220665 only For pump Model 237010 only02335 For pump Model 220668 only For pump Model 237013 onlyRef No Air Control Valve Ref No Pilot Valve Repair and Conversion Kits 220948 SEAT, carbide 108822 Repair and Conversion Kits Filter, Regulator, Lubricator Kit Filter, Regulator, Lubricator FRL KitDrum Cover Kit and Return Tube Kit Drum Cover KitReturn Tube Kit Return TubeSuction Kit Suction KitTechnical Data, 400 Series Pumps Performance Chart, 400 Series PumpsModel 220663 Model 220666Technical Data, 1200 Series Pumps Performance Chart, 1200 Series PumpsModel 220664 Model 220667Technical Data, 2500 Series Pumps Performance Chart, 2500 Series PumpsModel 220665 Model 220668Dimensional Drawing Mounting Hole LayoutGraco Standard Warranty Graco Information
Top Page Image Contents