Euro-Pro 374 Sewing Buttonholes Model 377, Sewing Buttonholes Model 373/372, Sewing Zippers

SEWING BUTTONHOLES (Model 377 and 374)

1. Set the pattern selector at¡°¡±			. Then pass the needle thread
	throughthe opening in the buttonhole foot and draw both needle
	and bobbin threads to the left side. Turn the balance wheel
	towards you until the needle comes to the point (1).
2.Lower the foot and sew slowly until the desired length is sewn,
then stop the machine at		(2).	°¡±
3.				.	Then sew
	Raise the needle and set the selector at
	several stitches of bar tack until the needle is at point (3).
4. Raise the needle and set the selector at					then sewthe
			°¡±
	right side of buttonhole the same length as the left side of
5.	buttonhole. Stop the machine at (4).
			°¡±	then sew several
	Raise needle and set the selector at
	stitches of final bar tack. Stop the machine with the needle at
					¡°	§
	point (5). . To lock threads, set the pattern selector at					B	(zero
	point of zigzag width).	And sew a few stitches.

6.Cut thebuttonhole open carefully using a seam ripper, taking care not to damage the bar tacks.

(Model EP 377 and 374 only)

English

SEWING BUTTONHOLES (Model 373/372)

1.	¡°¡±	Then pass the needle thread
	Set the pattern selector at
	through the opening in the buttonhole foot and draw both of
	needle and bobbin threads to the right side. Turn the balance
	wheel towards you until the needle comes to the point (1).
2. Lower the foot and sew slowly until a desired length is sewn,
3.	then stop the machine at (2).	¡°¡±
			then sew
	Raise the needle and set the selector at
4.	several stitches of bar tack until the needle is at point (3).
		¡°¡±	then sew the
	Raise the needle and set the selector at
	left side of buttonhole just as the same length as the right side of
5.	buttonhole. Stop the machine at	(4).
		¡°¡±	then sew several
	Raise the needle and set the selector at
	stitches of final bar tack. Stop the machine with the needle at
	point (5).

6.Cut the buttonhole open carefully using a seam ripper, taking care not to damage the bar tacks.

Note: To make a heavier buttonhole, sew twice by repeating the same procedure.

( Model 373/372 )

SEWING ZIPPERS

	Model 377		Model 374		Model 373/372
Presser foot	zipper foot		zipper foot		zipper foot
Pattern selector	M(	)	A(	)	1-3(	)
Stitch length dial	1 to 4		1 to 4

Raise the foot and the needle to its highest position by turning the balance wheel towards you. Replace the foot with the zipper foot.

1.Pin or baste the zipper tape to the fabric and place the work- piece in position under the foot.

Attach snap on zipper foot so that the needle passes on its left hand side.

*When starting sewing, both needle and bobbin threads ends should be put away under the foot.

2.Sew on the right side of the zipper by guiding Zipper teeth as close as possible to the needle drop. Before the foot reaches the slider on the zipper tape, raise the foot and open the zipper by keeping the needle in the fabric.

Lower the foot and sew on the remaining of the seam,

3.To sew the left side zipper change position of foot to bring the foot to the left side of the needle. Sew on in the same way as you did on the right side of zipper.

Zipper foot

	tape
	Elements
	Fabric
	Slider
Elements	Fia. 1
	Slider

Element

Zipper foot Needle

Fabric

Tape Element

15