Pella 818L0100 installation instructions Rough Opening Preparation

Page 2

The performance of any building is dependent upon the design, installation, and workmanship of the entire building system. Pella Corporation strongly recommends consulting an experienced architect, contractor or structural engineer prior to installation of Pella products.

The individual (building owner, architect, contractor, installer and/or consumer) responsible for the project must take into account local conditions, building codes, inherent component limitations, the effects of aging and weathering on building components, and other design issues relevant to each project.

The determination of the suitability of all building components for each project, as well as the design and installation of flashing and sealing systems, are the responsibility of the building owner, architect, contractor, installer and/or consumer.

YOU WILL NEED TO SUPPLY:

• Cedar or Impervious shims/spacers (12 to 20)

• 2" galvanized roofing nails (1/4 lb.)

• #10 x 3-1/2” corrosion resistant wood screws

(Performance Upgrade & HurricaneShield)

•Masonry screws for concrete applications (Minimum of 3/16’ diameter x 3”)

•Closed cell foam backer rod/sealant backer

(21 to 30 ft.)

• Pella® SmartFlash™ foil backed butyl window and

door flashing tape or equivalent

• High quality exterior grade polyurethane or silicone

sealant (2 to 3 tubes per door)

SEALANT

•Great Stuff™ Window and Door Insulating Foam Sealant by the Dow Chemical Company or equivalent low pressure polyurethane window and door foam - DO NOT use high pressure or latex foams

•Sill pan (optional)

6-5/8” x (Rough Opening Width +2)

•Pella aluminum sill support or wood blocking

•Interior trim and/or jamb extensions (15 to 40 ft.

Installation Clip Option:

•6” or 8” installation clips

•#6 x 5/8” corrosion resistant flat head wood screws

•#8 x 1-1/2” corrosion resistant screws or 3/16” x 1-1/2” masonry screws

TOOLS REQUIRED:

• Tape measure

•Level

•Square

• Hammer

• Stapler

• Sealant Gun

• Scissors or utility knife

•Tin Snips

•Screwdrivers (#2 Phillips with 8” shaft and small flat blade)

•T20 Torx Wrench (Architect Series®)

•1/8" Allen wrench (Designer Series®)

• Drill

• Drill Bits 13/64” and

1/8” and masonry bit for

concrete applications

A L L D O O R S • A L L D O O R S

1 ROUGH OPENING

PREPARATION

A.Confirm the opening is plumb and level. Note: It is critical that the bottom is level.

B.Confirm the door will fit the opening. Measure all four sides of the opening to make sure it is 3/4” larger than the door in width and 1/2” larger in height.

Measure the width at the top, bottom, and center. Measure the height at the far left side, the far right side, and in the center.

Note: 1-1/2” or more of solid wood blocking is required around the perimeter of the opening. Fix any problems with the rough opening before proceeding.

Interior

1A

Interior

1B

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Important Safety Information Rough Opening Preparation Cut the water resistive barrier For Doors Using Optional Sill Pan Go To StepS a L L D O O R S a L L D O O R S In-swing doorsD O O R S a L L D O O R S a L L L D O O R SO R S a L L D O O R S D O O R S aS a L L D O O R S a L L D O O R S a L L Prepare the Door for InstallationO R S L L D O O R S a L L D OR a D E & H U R R I C a N E S H I E L D D O O Setting Fastening DoorApplications for Performance Upgrade and HurricaneShield R F O R M a N C E UPlumb and square door. Place shims at each O R S a L LInsert the door from the exterior Double doors with center latch Fasten the door to openingS a L L D O O R S a L L L L D O O R SO R S a L L D O O R S a L L D O O R O R S a L L D OO R S a L L D O O R S a L L D O O R S a L Integrating the Door to the Water Resistive BarrierO O R S a L L D O O R S a L L D O O R Fold down top flapI C a N E S H I E L D R M a N C E U P G R a D EO R S P E R E & H USecure the jambs and head of the door I E L D D O O R S P E R F O R M a N C E U P G R a D ER F O R M a N C E U P G R a D E & H U R R I C a N E L L D O O R S a L L D O O R S Interior SealL D O O R S L D O O RO R S a L L D O O R S a L L D O O R S Sealing the Door to Exterior Wall CladdingL D O O R S a L L Apply a bead of high quality exterior gradeExterior Finishing Care and Maintenance Important NoticeInterior Finishing Troubleshooting Adjustable Strike Latching Issues L D O O R S a L L D O

818L0100 specifications

The Pella 818L0100 is a standout entry in Pella's impressive lineup of high-performance windows and doors, designed for both residential and commercial applications. Renowned for its robust construction and aesthetic appeal, the 818L0100 combines advanced technology with exceptional energy efficiency, making it a popular choice for modern architecture.

One of the main features of the Pella 818L0100 is its dual-pane insulating glass, which significantly reduces energy loss. This feature is crucial for maintaining comfortable indoor temperatures throughout the year, whether in the heat of summer or the chill of winter. The glass is treated with a low-emissivity (Low-E) coating that helps to minimize UV exposure while allowing natural light to flood in. This innovative technology not only contributes to energy savings but also helps protect furnishings and flooring from fading.

The construction of Pella windows is another highlight. The 818L0100 is made with high-quality materials, including wood, fiberglass, or vinyl, providing durability and a wide range of aesthetic options. The wood interior can be customized with various finishes, while the exterior can withstand even the harshest weather conditions without fading or peeling.

For added convenience and security, the Pella 818L0100 features multi-point locking systems that offer improved protection against potential break-ins. The integrated features do not compromise the window's elegant design, blending seamlessly into any architectural style.

The ease of operation is another characteristic of this window model. Available in various configurations, including casement, double-hung, and sliding styles, it caters to different preferences and functional needs. It also includes weather stripping that helps prevent air and water infiltration, ensuring a tight seal.

Furthermore, Pella has made strides in sustainability with the 818L0100 by using responsibly sourced materials and eco-friendly manufacturing processes. This commitment not only enhances the window's appeal for environmentally-conscious consumers but also aligns with today’s demand for greener living solutions.

In summary, the Pella 818L0100 stands out in the market for its combination of energy efficiency, durable construction, security features, and aesthetic flexibility, making it an intelligent choice for homeowners and builders alike looking to blend functionality with style. The Pella brand's commitment to quality and innovation ensures that the 818L0100 will meet the needs of various building projects while providing long-lasting performance.
Top Page Image Contents