Pella 818L0100 Double doors with center latch, Fasten the door to opening

Page 8

D O O R S • A L L D O O R S • A L L D O O R S • A L L D O O R S • A L L D O O R S • A L L D O O R S • A L L D O O R S

F. Fasten the door to opening

 

by driving 2” galvanized

 

roofing nails into each

 

pre-punched hole in the

 

nailing fin.

3F

 

Note: Make sure the fin

 

corner is lying as flat

as

 

possible.

 

 

G. Carefully open the door(s) and remove all

3H

shipping spacers.

 

 

 

Note: Be sure to remove the spacers from the bottom edge of the door panel.

Double doors with center latch:

Designer Series Only: Use the construction handle to operate the active door handle.

Operate the flushbolts per the instructions on the label on the strike located on the astragal.

Architect Series Only: Use the construction handle to operate both the active and passive door panels.

H. For Designer Series Only: Install sill screws. Place a dab of sealant in each of the pre- drilled holes in the bottom of the unit (sill). Then insert a #8 x 2” corrosion resistant screw (provided) into each hole. For masonry floors us a 3/16” masonry screw in place of the provided screw, pilot drill per screw manufacturer’s recommendations.

For Architect Series Standard Installation Applications Only: Install sill screws. Remove the threshold screws and insert a #8 x 3” stainless steel screw (provided) into each hole. For masonry floors use a 3/16 masonry screw in place of the provided screw, pilot drill per screw manufacturer’s recommendations.

Note: On In-Swing Door Standard Installation, sill screws are not needed.

Sill screws for Architect Series Performance upgrade and doors with hurricaneshield impact-resistant glass are installed in Step 5.

I.For Low Profile Sills: through each installation

screw hole drill a 1/8” pilot; and install a #8 x 3” corrosion resistant screw (provided) into the pilot hole into the floor. For doors including a standard lock install tubs per instruction included with the sill strike package.

Note: For concrete floors use masonry screws that

 

are a minimum size of 3/16” diameter x 2” and

3K

pilot per manufacturer’s recommendations for

 

the screw.

 

J. Remove sill strike screws from the sill strike

3J

located on the door sill. Place a dab of sealant

 

into the three sill strike holes and install the three

 

#8 x 3” flat head stainless steel screws (provided)

 

into the holes.

 

Page 7 Page 9
Image 8
Page 7 Page 9
Contents
Important Safety Information Rough Opening Preparation For Doors Using Optional Sill Pan Go To Step S a L L D O O R S a L L D O O R SCut the water resistive barrier In-swing doorsL D O O R S O R S a L L D O O R SD O O R S a L L D O O R S a L L D O O R S aPrepare the Door for Installation O R SS a L L D O O R S a L L D O O R S a L L L L D O O R S a L L D OSetting Fastening Door Applications for Performance Upgrade and HurricaneShieldR a D E & H U R R I C a N E S H I E L D D O O R F O R M a N C E UPlumb and square door. Place shims at each O R S a L LInsert the door from the exterior Double doors with center latch Fasten the door to openingL L D O O R S O R S a L L D O O R S a L L D O O RS a L L D O O R S a L L O R S a L L D OIntegrating the Door to the Water Resistive Barrier O O R S a L L D O O R S a L L D O O RO R S a L L D O O R S a L L D O O R S a L Fold down top flapR M a N C E U P G R a D E O R S P E RI C a N E S H I E L D E & H USecure the jambs and head of the door I E L D D O O R S P E R F O R M a N C E U P G R a D ER F O R M a N C E U P G R a D E & H U R R I C a N E Interior Seal L D O O R SL L D O O R S a L L D O O R S L D O O RSealing the Door to Exterior Wall Cladding L D O O R S a L LO R S a L L D O O R S a L L D O O R S Apply a bead of high quality exterior gradeExterior Finishing Care and Maintenance Important NoticeInterior Finishing Troubleshooting Adjustable Strike Latching Issues L D O O R S a L L D O
Related manuals
Manual 16 pages 33.12 Kb