Pella 818L0100 Integrating the Door to the Water Resistive Barrier, Fold down top flap

Page 10

S • A L L D O O R S

4 INTEGRATING THE DOOR TO THE WATER RESISTIVE BARRIER

Note: The flashing tape must be applied approximately 1/2" onto the frame cladding at the jambs and head. Pre-folding the tape at 1/2" before removing the paper backing will make it easier to apply the tape correctly. If the siding is less than 1/2" thick, adjust the dimension of the fold so the exterior sealant line will cover the exterior edge of the tape.

L D O O R S • A L L D O O R S • A L L D O O R

A.Apply side flashing tape. Cut two pieces of flashing tape 4" longer than the frame height of the door. Apply one piece 1/2" onto the frame cladding, over the nailing fin and onto the water resistive barrier on each side. The tape should extend 2" above the top of the door and 2" below the bottom of the door. Press the tape down firmly while folding down the excess tape at the top and bottom of the door.

B.Apply top flashing tape. Cut a piece of flashing tape long enough to go across the top of the door and extend at least 1" past the side flashing tape on both sides. Apply the tape 1/2" onto the frame cladding, over the top nailing fin as shown. Fold the overlapping tape down, and press all tape down firmly.

C. Fold down top flap of

Exterior

4C

 

water resistive barrier.

Exterior

4A

4B

Exterior

 

 

1"

D O O R S • A L L D O O R S • A L L D O O R S • A L

4D

D. Apply flashing tape to diagonal cuts. Cut pieces of flashing tape at least 1" longer than the diagonal cuts in the water resistive barrier. Apply the tape covering the entire diagonal cut in the water resistive barrier at both upper corners of the door.

Note: Be sure to overlap the top corners.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents
Important Safety Information Rough Opening Preparation Cut the water resistive barrier For Doors Using Optional Sill Pan Go To StepS a L L D O O R S a L L D O O R S In-swing doorsD O O R S a L L D O O R S a L L L D O O R SO R S a L L D O O R S D O O R S aS a L L D O O R S a L L D O O R S a L L Prepare the Door for InstallationO R S L L D O O R S a L L D OR a D E & H U R R I C a N E S H I E L D D O O Setting Fastening DoorApplications for Performance Upgrade and HurricaneShield R F O R M a N C E UInsert the door from the exterior O R S a L LPlumb and square door. Place shims at each Double doors with center latch Fasten the door to openingS a L L D O O R S a L L L L D O O R SO R S a L L D O O R S a L L D O O R O R S a L L D OO R S a L L D O O R S a L L D O O R S a L Integrating the Door to the Water Resistive BarrierO O R S a L L D O O R S a L L D O O R Fold down top flapI C a N E S H I E L D R M a N C E U P G R a D EO R S P E R E & H UR F O R M a N C E U P G R a D E & H U R R I C a N E I E L D D O O R S P E R F O R M a N C E U P G R a D ESecure the jambs and head of the door L L D O O R S a L L D O O R S Interior SealL D O O R S L D O O RO R S a L L D O O R S a L L D O O R S Sealing the Door to Exterior Wall CladdingL D O O R S a L L Apply a bead of high quality exterior gradeInterior Finishing Care and Maintenance Important NoticeExterior Finishing Troubleshooting Adjustable Strike Latching Issues L D O O R S a L L D O
Related manuals
Manual 16 pages 33.12 Kb