Pella 818L0100 Prepare the Door for Installation, S a L L D O O R S a L L D O O R S a L L

Page 5

D O O R S

R.Cut a piece of flashing tape to the width of the opening. Install to the flanges of the sill pan and overlap the tape from step 1N by 1”. If needed add a second or third piece of flashing tape until the sill pan is covered to the interior sill pan lip.

Note: The purpose of this tape is to seal the sill screws when installing the door.

O R S • A L L D O O R S • A L L D O O R S • A L L

S.Cut two pieces of flashing tape 1-1/2” x 6” and apply to the bottom corners of the opening by beginning in the corner of the sill pan, with 3/4” of the tape applied to the sill pan and 3/4” of the tape applied to the side flange. The remainder of the tape is to be at a 45 degree angle onto the exterior.

T.Attach the aluminum sill support or wood blocking to the exterior of the box plate to support the edge of the door sill. Place the sill support flush with the subfloor.

1S

1R

LIP

1"

1T

LIP

S • A L L D O O R S • A L L D O

2 PREPARE THE DOOR FOR INSTALLATION

TWO OR MORE PEOPLE WILL BE REQUIRED TO HANDLE THE PANEL AND FRAME SAFELY.

A.Remove plastic wrap and cardboard packaging from door. Do not remove plastic shipping spacers. The shipping spacers will help keep the door square during installation. Do not unlock or open the door until it is fully fastened.

Designer Series only:

DO NOT cut the strap that goes from the lock holes to the sill of the door.

Note: If grilles or hardware are removed from the door at this time, label them and store them in a protected area.

• A L L D O O R

B.Fold out installation fin to 90°. Be careful not to remove or tear the fin corners

Note: If the fin corner is not at 90°, the door will not line up correctly on the interior.

Standard Fin Application go to Step 3

2B

D O O R S

Applications for Performance Upgrade and HurricaneShield product requires additional clip installation or screw installation. Clip installation prep is included in Step 2C. Screw installation steps are included in Step 5.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents
Important Safety Information Rough Opening Preparation S a L L D O O R S a L L D O O R S For Doors Using Optional Sill Pan Go To StepCut the water resistive barrier In-swing doorsO R S a L L D O O R S L D O O R SD O O R S a L L D O O R S a L L D O O R S aO R S Prepare the Door for InstallationS a L L D O O R S a L L D O O R S a L L L L D O O R S a L L D OApplications for Performance Upgrade and HurricaneShield Setting Fastening DoorR a D E & H U R R I C a N E S H I E L D D O O R F O R M a N C E UPlumb and square door. Place shims at each O R S a L LInsert the door from the exterior Fasten the door to opening Double doors with center latchO R S a L L D O O R S a L L D O O R L L D O O R SS a L L D O O R S a L L O R S a L L D OO O R S a L L D O O R S a L L D O O R Integrating the Door to the Water Resistive BarrierO R S a L L D O O R S a L L D O O R S a L Fold down top flapO R S P E R R M a N C E U P G R a D EI C a N E S H I E L D E & H USecure the jambs and head of the door I E L D D O O R S P E R F O R M a N C E U P G R a D ER F O R M a N C E U P G R a D E & H U R R I C a N E L D O O R S Interior SealL L D O O R S a L L D O O R S L D O O RL D O O R S a L L Sealing the Door to Exterior Wall CladdingO R S a L L D O O R S a L L D O O R S Apply a bead of high quality exterior gradeExterior Finishing Care and Maintenance Important NoticeInterior Finishing L D O O R S a L L D O Troubleshooting Adjustable Strike Latching Issues
Related manuals
Manual 16 pages 33.12 Kb