Installation | ADTRAN TSU 120e instruction

Chapter 2. Installation

mentary equipment grounding conductor shall be in compli- ance with the rules for terminating bonding jumpers at Part K or Article 250 of the National Electrical Code, ANSI/NFPA 70. Termination of the supplementary equipment grounding con- ductor is permitted to be made to building steel, to a metal electrical raceway system, or to any grounded item that is per- manently and reliably connected to the electrical service equip- ment ground.

Bare, covered, or insulated grounding conductors are accept- able. A covered or insulated grounding conductor shall have a continuous outer finish that is either green, or green with one or more yellow stripes.

The supplemental grounding conductor shall be connected to the equipment using a number 8 ring terminal. The terminal should be fastened to the grounding lug provided on the rear panel of the equipment. The ring terminal should be installed using the appropriate crimping tool (AMP P/N 59250 T-EAD Crimping Tool or equivalent).

61202129L1-1

TSU 120 User Manual

2-3

Image 31

ADTRAN TSU 120e user manual Installation

Contents

Part Number 1202129L1 1202129L2 TSU 120 & 120e Trademarks Y2K Project Line Adtran Web Site Product Matrix Faxback Document LineMail Page REN/SOC FIC Usoc Page Canadian Emissions Requirements Canadian Equipment Limitations Affidavit Requirements for Connection To Digital Services Page Page Important Safety Instructions Warranty and Customer Service Xiv Table of Contents Chapter Status Menu Chapter Operation Chapter Utility Menu Chapter Configuration Menu Chapter Telnet/Terminal Menus Chapter Test Menu Index Index-1 Table of Contents List of Figures List of Figures List of Tables List of Tables TSU 120 Overview Introduction Standard Features in the TSU BR1TE TSU Option ModulesOCU DP DSU DP Option Module Architecture TSU 120 Configuration ApplicationsRouter, PBX, Video Conferencing Applications Customer Provides UNPACK, INSPECT, Power UPReceipt Inspection Adtran Shipments Include Grounding Instructions Power Connection Installation TSU 120e Rear Panel Identification of Rear Panel Layout Network Test Interface TSU 120 InterfacesNx56/64 Serial Interface TSU 120e only Chain Port Output DSX-1 PBX InterfaceDSX-1 Test Interface Chain Port Input Set User Passcode Power Up TestingSelf-Test Initialization Chain-In PC Set Chain Port InputChain-in/Chain Out Power-Up Procedure Installation Front Panel Descriptions Name Front Panel Button. See Operation Keys on LED Descriptions CSU Status TSU 120 Front Panel Layout Module Status DSU/DSX Status General Menu Operation Operation Keys Step Action Select and Activate a Menu Item Display Only Data Fields Set the Data Field Exit Any Menu Field Operation Or Display Data Port Identification Util Utilities Config ConfigurationFront Panel Menu Structure Status Watch Pro Adtran PC Program Alternate Methods of ControlWatch Pro/LAN Connection Snmp Watch Pro/EIA-232 Connection Telnet Terminal Mode Status Menu Network Interface Performance Report Network Performance Reports NI Perf Rpts Active Alarms Network Interface Errors NI Errors Port Status View History DBU Data/CNTRL TSU 120e only Nx56/64 Menu Items DTE Data/ClockDTE Status Port Rate YES/NO indication of active DBU status DSX-1 Menu Items DSX-1 ErrorsDBU Contrl TSU 120e only DBU Status TSU 120e only Remote Port Clear Port Alarm Clear Port AlmEnet Status TSU 120e only Status Menu Configuration Menu Complete Configuration Menu Network NI Menu Items Network NIMenu Item Description BIT SET LBOInband Lpbck TSU 120 Clock Sources Network Timed Clock Source Network Timed DSX-1 Timed Clock Source Base DSX-1 Timing DTE Timed Clock Source DTE Timing Internal Clock Source Internal Timing Secondary Timing Normal CSU Normal CSU Timing Unit Menu Mask DefaultIP Address Subnet Auto Map Exchange Map XchngMap In Use AB OFF Review MAP AB DS0 Map a and DS0 Map BCopy a B Temp Create Temp DSO Map Example Review TempEdit Temp Apply Temp AB Create Temp Selection Screen DS0 Rate Port Configuration Port ConfigNx56/64 Port Configuration Port Config Menu Items Nx56/64 Menu Items Description DSR DataCTS DCD Normal Mode of Operation Inband ModeTX CLK Source Backup Delay DBU Configuration Menu Items TSU 120e onlyBackup Mode Backup on Testing Restore DelayRetry Delay Backup Yellow Alarm Enable HRDisable HR DSX-1 Port Configuration Port Config Menu Items Loopback SignalingLine Length FT IN-BAND Utility Menu Complete Utility Menu Tree If you want to Do this Factory Restore Fact RestoreTime/Date Set Passcode No Passcode Desired Unit IDChange/Set a Passcode Passcode Automatic Time-out Enet Address TSU 120e only CMD ModeSoftware Revision Software Rev Port Utility Option Ports Utility Menu Test Menu Complete Test Menu Tree Line Loopback Network TestsLoopback Tests Network Interface Loopbacks Activates the line loopback Network Loopback Tests All Ones Test Patterns All ZerosQrss Pattern Example Terminates pattern generation Run Self-test Port Tests Loop is deactivated Port Test Menu Items for 0.1 Nx56/64 DBU TST Result TSU 120e only Cancel TestsDBU Loopback TSU 120e only DBU Test TSU 120e only Telnet/Terminal Main Menu Main Menu DS0 Maps Configuration Menu Status, Config, Util, and Test Menu Options Initializing the Temp Map Map ConfigurationIf you want to Use these selections Reviewing Maps Editing the Temp MapExplanation Applying the Temp Map Management Configuration Remote Menu AccessUnit Access Table Unit Access Table Add New Unit Snmp Read Community Default Unit PasscodeModify Unit Delete Unit Host 3 Trap IP Address Snmp Trap CommunityHost 1 Trap IP Address Host 2 Trap IP Address Auth. Fail Traps Sent Telnet/Terminal TimeoutTelnet/Terminal Password System Location Quit Session Flash Download Agent About SnmpBasic Components Network Manager GetNextRequest CommandsMessages GetRequest Trap TSU 120 Snmp Access Snmp Trap Configuration Table A-1. How to Configure Network Manager MIB Snmp MIB Browser Configuration Ftp.adtran.com Snmp MIB Files Supported by the TSUStandard MIBs Adtran Enterprise-specific MIBs Adtran Product MIB ADTRAN.MIB Appendix B Understanding TR-08 Felp Table B-1. Alarm ConditionsOOF TR-08 Channel Number Port TR-08 DS0 Conversion TableTable B-2.TR-08 DS0 Conversion Table DS0 Appendix B. Understanding TR-08 Table C-1. Network Pinouts WiringNetwork Pinouts Connections Table C-2. Control In/Chain in Pinout Control In/Chain Table C-3. Chain Out Pinout Chain Out Nx56/64 DTE Connector type Part numberTable C-4. V.35 Pinout Nx56/64 DTE Table C-5. Pinout Connectors for Modular Jack Interface Connector type RJ-48CBase DSX-1 PBX Pin Name to NIC Connector type Usoc10BaseT TSU 120e only Table C-6 BaseT Ethernet TSU 120e only Network Interface NI Alarm MessagesNx56/64 Interface Status Messages Following messages indicate the status of the Nx56/64 card Appendix D. System Messages T1/FT1 Interface Electrical SpecificationsCompatibility CTS, DCD, DSR Nx56/64 V.35 InterfaceDSX-1 Interface Option Slot Interface Chassis SpecificationsManagement Interfaces Chain In/Out Ports Max Power Environmental SpecificationsInput Power Fuse Operating Temperature Numerics Index GetNextRequest Snmp A-5 Index-4 61202129L1-1 Index-5 Index-6 61202129L1-1 Post-Sale Support Presales Inquiries and Applications SupportRepair and Return