Terminates pattern generation, Example | ADTRAN TSU 120e guide

Chapter 7. Test Menu

QRSS ALL DS0S Generates a QRSS test pattern and inserts the pattern into all DS0s

QRSS TST DS0S Inserts a QRSS pattern in those DS0s mapped as TST in the currently active map (A or B)

NONE	Terminates pattern generation

QRSS always runs at 64K/DS0.

Example

1.Select QRSS ALL DS0S by using the Arrow Keys.

2.Press Enter to record the selection. The TSU 120 starts to gen- erate a QRSS test pattern and inserts the pattern into all DS0s.

3.To end the test, select NONE.

PATTERN RESULT

Displays the results of the test currently active. Leaving and returning to this menu item does not interrupt the test.

Pressing 2 injects errors into the test pattern. These errors are detected by the device performing the pattern check.

ES The number of seconds with at least 1 bit error.

BES The number of seconds with more than 1 bit error and less than 320.

SES The number of seconds with more than 320 bit errors.

SYNC Indicates if pattern sync is (yes) or is not (no) valid. An asterisk (*) indicates if pattern sync has been lost since the start of testing.

7-6

TSU 120 User Manual

61202129L1-1

Image 94

ADTRAN TSU 120e user manual Terminates pattern generation, Example

Contents

TSU 120 & 120e Part Number 1202129L1 1202129L2 Trademarks Y2K Project Line Adtran Web Site Product Matrix Faxback Document LineMail Page REN/SOC FIC Usoc Page Canadian Emissions Requirements Canadian Equipment Limitations Affidavit Requirements for Connection To Digital Services Page Page Important Safety Instructions Warranty and Customer Service Xiv Table of Contents Chapter Operation Chapter Status Menu Chapter Configuration Menu Chapter Utility Menu Chapter Test Menu Chapter Telnet/Terminal Menus Index Index-1 Table of Contents List of Figures List of Figures List of Tables List of Tables Introduction TSU 120 Overview Standard Features in the TSU DSU DP TSU Option ModulesOCU DP BR1TE Option Module Architecture TSU 120 Configuration ApplicationsRouter, PBX, Video Conferencing Applications Adtran Shipments Include UNPACK, INSPECT, Power UPReceipt Inspection Customer Provides Power Connection Grounding Instructions Installation Identification of Rear Panel Layout TSU 120e Rear Panel Network Test Interface TSU 120 InterfacesNx56/64 Serial Interface TSU 120e only Chain Port Input DSX-1 PBX InterfaceDSX-1 Test Interface Chain Port Output Initialization Power Up TestingSelf-Test Set User Passcode Chain-In PC Set Chain Port InputChain-in/Chain Out Power-Up Procedure Installation Front Panel Front Panel Descriptions Name LED Descriptions CSU Status Button. See Operation Keys on TSU 120 Front Panel Layout DSU/DSX Status Module Status Operation Keys General Menu Operation Select and Activate a Menu Item Step Action Set the Data Field Display Only Data Fields Data Port Identification Exit Any Menu Field Operation Or Display Status Config ConfigurationFront Panel Menu Structure Util Utilities Watch Pro Adtran PC Program Alternate Methods of ControlWatch Pro/LAN Connection Watch Pro/EIA-232 Connection Snmp Terminal Mode Telnet Status Menu Network Performance Reports NI Perf Rpts Network Interface Performance Report Network Interface Errors NI Errors Active Alarms View History Port Status Port Rate Nx56/64 Menu Items DTE Data/ClockDTE Status DBU Data/CNTRL TSU 120e only DBU Status TSU 120e only DSX-1 Menu Items DSX-1 ErrorsDBU Contrl TSU 120e only YES/NO indication of active DBU status Remote Port Clear Port Alarm Clear Port AlmEnet Status TSU 120e only Status Menu Configuration Menu Complete Configuration Menu Network NI Menu Items Network NIMenu Item Description Lpbck SET LBOInband BIT TSU 120 Clock Sources Network Timed Network Timed Clock Source Base DSX-1 Timing DSX-1 Timed Clock Source DTE Timing DTE Timed Clock Source Internal Timing Internal Clock Source Secondary Timing Normal CSU Timing Normal CSU Unit Menu Subnet DefaultIP Address Mask OFF Map Exchange Map XchngMap In Use AB Auto Create Temp DS0 Map a and DS0 Map BCopy a B Temp Review MAP AB Apply Temp AB Review TempEdit Temp DSO Map Example Create Temp Selection Screen Nx56/64 Menu Items Description Port Configuration Port ConfigNx56/64 Port Configuration Port Config Menu Items DS0 Rate DCD DataCTS DSR Normal Mode of Operation Inband ModeTX CLK Source Backup on DBU Configuration Menu Items TSU 120e onlyBackup Mode Backup Delay Backup Restore DelayRetry Delay Testing DSX-1 Port Configuration Port Config Menu Items Enable HRDisable HR Yellow Alarm IN-BAND SignalingLine Length FT Loopback Utility Menu Complete Utility Menu Tree Set Passcode Factory Restore Fact RestoreTime/Date If you want to Do this Passcode Automatic Time-out Unit IDChange/Set a Passcode No Passcode Desired Port Utility Option Ports CMD ModeSoftware Revision Software Rev Enet Address TSU 120e only Utility Menu Test Menu Complete Test Menu Tree Network Interface Loopbacks Network TestsLoopback Tests Line Loopback Network Loopback Tests Activates the line loopback All Ones Test Patterns All ZerosQrss Pattern Terminates pattern generation Example Run Self-test Port Tests Port Test Menu Items for 0.1 Nx56/64 Loop is deactivated DBU Test TSU 120e only Cancel TestsDBU Loopback TSU 120e only DBU TST Result TSU 120e only Main Menu Telnet/Terminal Main Menu Status, Config, Util, and Test Menu Options DS0 Maps Configuration Menu Initializing the Temp Map Map ConfigurationIf you want to Use these selections Applying the Temp Map Editing the Temp MapExplanation Reviewing Maps Management Configuration Remote Menu AccessUnit Access Table Unit Access Table Add New Unit Delete Unit Default Unit PasscodeModify Unit Snmp Read Community Host 2 Trap IP Address Snmp Trap CommunityHost 1 Trap IP Address Host 3 Trap IP Address System Location Telnet/Terminal TimeoutTelnet/Terminal Password Auth. Fail Traps Sent Flash Download Quit Session Network Manager About SnmpBasic Components Agent GetRequest CommandsMessages GetNextRequest TSU 120 Snmp Access Trap Snmp Trap Configuration Snmp MIB Browser Configuration Table A-1. How to Configure Network Manager MIB Adtran Product MIB ADTRAN.MIB Snmp MIB Files Supported by the TSUStandard MIBs Adtran Enterprise-specific MIBs Ftp.adtran.com Appendix B Understanding TR-08 Felp Table B-1. Alarm ConditionsOOF DS0 TR-08 DS0 Conversion TableTable B-2.TR-08 DS0 Conversion Table TR-08 Channel Number Port Appendix B. Understanding TR-08 Connections WiringNetwork Pinouts Table C-1. Network Pinouts Control In/Chain Table C-2. Control In/Chain in Pinout Chain Out Table C-3. Chain Out Pinout Nx56/64 DTE Connector type Part numberTable C-4. V.35 Pinout Nx56/64 DTE Table C-5. Pinout Connectors for Modular Jack Interface Connector type RJ-48CBase DSX-1 PBX Table C-6 BaseT Ethernet TSU 120e only Connector type Usoc10BaseT TSU 120e only Pin Name to NIC Network Interface NI Alarm MessagesNx56/64 Interface Status Messages Following messages indicate the status of the Nx56/64 card Appendix D. System Messages T1/FT1 Interface Electrical SpecificationsCompatibility CTS, DCD, DSR Nx56/64 V.35 InterfaceDSX-1 Interface Chain In/Out Ports Chassis SpecificationsManagement Interfaces Option Slot Interface Fuse Operating Temperature Environmental SpecificationsInput Power Max Power Index Numerics GetNextRequest Snmp A-5 Index-4 61202129L1-1 Index-5 Index-6 61202129L1-1 Post-Sale Support Presales Inquiries and Applications SupportRepair and Return