Port Configuration Port Config, DS0 Rate | ADTRAN TSU 120e instruction

Chapter 5. Configuration Menu

Port Configuration (Port Config)

Port Configuration selects and configures the parameters asso- ciated with any data port in the unit. For example, parameters for the DSX-1 (PBX) interface are set through this menu. The items that can be set depend on which option module is installed. The list of option ports will vary with the configura- tion.

The TSU 120 is designed so that any additional ports devel- oped in the future will contain the appropriate menu selections to provide access by use of this menu item.

The Config menus for options ports are described in separate sections of the manual supplied with the option card.

0.1 Nx56/64 Port Configuration (Port Config) Menu Items

There are two major menu items under Nx/DBU configura- tion: NX56/64 CONFIG and DBU CONFIG. Only the TSU 120e offers the DBU feature.

Nx56/64 Menu Items

Menu Item	Description

DS0 RATE	This sets the base rate of the interface. The
	actual data rate depends on the number of
	DS0s assigned to the Nx port.
	Choices: 56K, 64K

TX CLK CNTRL	Controls the clock used by the TSU 120 to
	accept transmit (TX) data from the DTE. The
	default is normal. If the interface cable is
	long, causing a phase shift in the data, the
	clock can be selected as Invert. This switches
	the phase of the clock which should
	compensate for a long cable.
	Choices: Normal, Invert

5-18

TSU 120 User Manual

61202129L1-1

Image 76

ADTRAN TSU 120e Nx56/64 Port Configuration Port Config Menu Items, Nx56/64 Menu Items Description, DS0 Rate

Contents

TSU 120 & 120e Part Number 1202129L1 1202129L2 Trademarks Y2K Project Line Adtran Web Site Product Matrix Faxback Document LineMail Page REN/SOC FIC Usoc Page Canadian Emissions Requirements Canadian Equipment Limitations Affidavit Requirements for Connection To Digital Services Page Page Important Safety Instructions Warranty and Customer Service Xiv Table of Contents Chapter Operation Chapter Status Menu Chapter Configuration Menu Chapter Utility Menu Chapter Test Menu Chapter Telnet/Terminal Menus Index Index-1 Table of Contents List of Figures List of Figures List of Tables List of Tables Introduction TSU 120 Overview Standard Features in the TSU TSU Option Modules OCU DPDSU DP BR1TE Option Module Architecture TSU 120 Configuration ApplicationsRouter, PBX, Video Conferencing Applications UNPACK, INSPECT, Power UP Receipt InspectionAdtran Shipments Include Customer Provides Power Connection Grounding Instructions Installation Identification of Rear Panel Layout TSU 120e Rear Panel Network Test Interface TSU 120 InterfacesNx56/64 Serial Interface TSU 120e only DSX-1 PBX Interface DSX-1 Test InterfaceChain Port Input Chain Port Output Power Up Testing Self-TestInitialization Set User Passcode Chain-In PC Set Chain Port InputChain-in/Chain Out Power-Up Procedure Installation Front Panel Front Panel Descriptions Name LED Descriptions CSU Status Button. See Operation Keys on TSU 120 Front Panel Layout DSU/DSX Status Module Status Operation Keys General Menu Operation Select and Activate a Menu Item Step Action Set the Data Field Display Only Data Fields Data Port Identification Exit Any Menu Field Operation Or Display Config Configuration Front Panel Menu StructureStatus Util Utilities Watch Pro Adtran PC Program Alternate Methods of ControlWatch Pro/LAN Connection Watch Pro/EIA-232 Connection Snmp Terminal Mode Telnet Status Menu Network Performance Reports NI Perf Rpts Network Interface Performance Report Network Interface Errors NI Errors Active Alarms View History Port Status Nx56/64 Menu Items DTE Data/Clock DTE StatusPort Rate DBU Data/CNTRL TSU 120e only DSX-1 Menu Items DSX-1 Errors DBU Contrl TSU 120e onlyDBU Status TSU 120e only YES/NO indication of active DBU status Remote Port Clear Port Alarm Clear Port AlmEnet Status TSU 120e only Status Menu Configuration Menu Complete Configuration Menu Network NI Menu Items Network NIMenu Item Description SET LBO InbandLpbck BIT TSU 120 Clock Sources Network Timed Network Timed Clock Source Base DSX-1 Timing DSX-1 Timed Clock Source DTE Timing DTE Timed Clock Source Internal Timing Internal Clock Source Secondary Timing Normal CSU Timing Normal CSU Unit Menu Default IP AddressSubnet Mask Map Exchange Map Xchng Map In Use ABOFF Auto DS0 Map a and DS0 Map B Copy a B TempCreate Temp Review MAP AB Review Temp Edit TempApply Temp AB DSO Map Example Create Temp Selection Screen Port Configuration Port Config Nx56/64 Port Configuration Port Config Menu ItemsNx56/64 Menu Items Description DS0 Rate Data CTSDCD DSR Normal Mode of Operation Inband ModeTX CLK Source DBU Configuration Menu Items TSU 120e only Backup ModeBackup on Backup Delay Restore Delay Retry DelayBackup Testing Enable HR Disable HRDSX-1 Port Configuration Port Config Menu Items Yellow Alarm Signaling Line Length FTIN-BAND Loopback Utility Menu Complete Utility Menu Tree Factory Restore Fact Restore Time/DateSet Passcode If you want to Do this Unit ID Change/Set a PasscodePasscode Automatic Time-out No Passcode Desired CMD Mode Software Revision Software RevPort Utility Option Ports Enet Address TSU 120e only Utility Menu Test Menu Complete Test Menu Tree Network Tests Loopback TestsNetwork Interface Loopbacks Line Loopback Network Loopback Tests Activates the line loopback All Ones Test Patterns All ZerosQrss Pattern Terminates pattern generation Example Run Self-test Port Tests Port Test Menu Items for 0.1 Nx56/64 Loop is deactivated Cancel Tests DBU Loopback TSU 120e onlyDBU Test TSU 120e only DBU TST Result TSU 120e only Main Menu Telnet/Terminal Main Menu Status, Config, Util, and Test Menu Options DS0 Maps Configuration Menu Initializing the Temp Map Map ConfigurationIf you want to Use these selections Editing the Temp Map ExplanationApplying the Temp Map Reviewing Maps Management Configuration Remote Menu AccessUnit Access Table Unit Access Table Add New Unit Default Unit Passcode Modify UnitDelete Unit Snmp Read Community Snmp Trap Community Host 1 Trap IP AddressHost 2 Trap IP Address Host 3 Trap IP Address Telnet/Terminal Timeout Telnet/Terminal PasswordSystem Location Auth. Fail Traps Sent Flash Download Quit Session About Snmp Basic ComponentsNetwork Manager Agent Commands MessagesGetRequest GetNextRequest TSU 120 Snmp Access Trap Snmp Trap Configuration Snmp MIB Browser Configuration Table A-1. How to Configure Network Manager MIB Snmp MIB Files Supported by the TSU Standard MIBs Adtran Enterprise-specific MIBsAdtran Product MIB ADTRAN.MIB Ftp.adtran.com Appendix B Understanding TR-08 Felp Table B-1. Alarm ConditionsOOF TR-08 DS0 Conversion Table Table B-2.TR-08 DS0 Conversion TableDS0 TR-08 Channel Number Port Appendix B. Understanding TR-08 Wiring Network PinoutsConnections Table C-1. Network Pinouts Control In/Chain Table C-2. Control In/Chain in Pinout Chain Out Table C-3. Chain Out Pinout Nx56/64 DTE Connector type Part numberTable C-4. V.35 Pinout Nx56/64 DTE Table C-5. Pinout Connectors for Modular Jack Interface Connector type RJ-48CBase DSX-1 PBX Connector type Usoc 10BaseT TSU 120e onlyTable C-6 BaseT Ethernet TSU 120e only Pin Name to NIC Network Interface NI Alarm MessagesNx56/64 Interface Status Messages Following messages indicate the status of the Nx56/64 card Appendix D. System Messages T1/FT1 Interface Electrical SpecificationsCompatibility CTS, DCD, DSR Nx56/64 V.35 InterfaceDSX-1 Interface Chassis Specifications Management InterfacesChain In/Out Ports Option Slot Interface Environmental Specifications Input PowerFuse Operating Temperature Max Power Index Numerics GetNextRequest Snmp A-5 Index-4 61202129L1-1 Index-5 Index-6 61202129L1-1 Post-Sale Support Presales Inquiries and Applications SupportRepair and Return