Map Exchange Map Xchng, Map In Use AB, Off, Auto | ADTRAN TSU 120

Chapter 5. Configuration Menu

Map Exchange (Map Xchng)

The MAP EXCHANGE menu enables and sets the automatic time of day map switch. The unit provides selection of the hour, minute, and seconds for the map switching to take place.

The menu items are:

Menu Item	Description

OFF	Indicates the map in use does not change
	(disabled).

AUTO	Indicates that the map in use will change at a
	user-selected time of day (enabled).

1.Scroll to select AUTO to enable or OFF to disable the Automatic Map Change feature.

2.Press Enter to activate the selection.

3.When AUTO is selected, the unit displays the screens to set times for switching.

4.After editing Map A, press Enter to record the Map A settings and activate the selection fields for Map B.

5.Use the same operation to edit switching time for Map B.

When ESF is used with an FDL channel between units, the units automatically coordinate the automatic map switch by sending a map switch command from end-to-end over the FDL. Only one end needs to be set to Auto for this to work.

Map In Use: A(B)

The MAP IN USE menu item controls the DS0 map the TSU 120 uses and displays the map in current use.

5-14

TSU 120 User Manual

61202129L1-1

Image 72

ADTRAN TSU 120e user manual Map Exchange Map Xchng, Map In Use AB, Off, Auto

Contents

TSU 120 & 120e Part Number 1202129L1 1202129L2 Trademarks Adtran Web Site Product Matrix Faxback Document Line Y2K Project LineMail Page REN/SOC FIC Usoc Page Canadian Emissions Requirements Canadian Equipment Limitations Affidavit Requirements for Connection To Digital Services Page Page Important Safety Instructions Warranty and Customer Service Xiv Table of Contents Chapter Operation Chapter Status Menu Chapter Configuration Menu Chapter Utility Menu Chapter Test Menu Chapter Telnet/Terminal Menus Index Index-1 Table of Contents List of Figures List of Figures List of Tables List of Tables Introduction TSU 120 Overview Standard Features in the TSU TSU Option Modules OCU DPDSU DP BR1TE TSU 120 Configuration Applications Option Module ArchitectureRouter, PBX, Video Conferencing Applications UNPACK, INSPECT, Power UP Receipt InspectionAdtran Shipments Include Customer Provides Power Connection Grounding Instructions Installation Identification of Rear Panel Layout TSU 120e Rear Panel TSU 120 Interfaces Network Test InterfaceNx56/64 Serial Interface TSU 120e only DSX-1 PBX Interface DSX-1 Test InterfaceChain Port Input Chain Port Output Power Up Testing Self-TestInitialization Set User Passcode Set Chain Port Input Chain-In PCChain-in/Chain Out Power-Up Procedure Installation Front Panel Front Panel Descriptions Name LED Descriptions CSU Status Button. See Operation Keys on TSU 120 Front Panel Layout DSU/DSX Status Module Status Operation Keys General Menu Operation Select and Activate a Menu Item Step Action Set the Data Field Display Only Data Fields Data Port Identification Exit Any Menu Field Operation Or Display Config Configuration Front Panel Menu StructureStatus Util Utilities Alternate Methods of Control Watch Pro Adtran PC ProgramWatch Pro/LAN Connection Watch Pro/EIA-232 Connection Snmp Terminal Mode Telnet Status Menu Network Performance Reports NI Perf Rpts Network Interface Performance Report Network Interface Errors NI Errors Active Alarms View History Port Status Nx56/64 Menu Items DTE Data/Clock DTE StatusPort Rate DBU Data/CNTRL TSU 120e only DSX-1 Menu Items DSX-1 Errors DBU Contrl TSU 120e onlyDBU Status TSU 120e only YES/NO indication of active DBU status Clear Port Alarm Clear Port Alm Remote PortEnet Status TSU 120e only Status Menu Configuration Menu Complete Configuration Menu Network NI Network NI Menu ItemsMenu Item Description SET LBO InbandLpbck BIT TSU 120 Clock Sources Network Timed Network Timed Clock Source Base DSX-1 Timing DSX-1 Timed Clock Source DTE Timing DTE Timed Clock Source Internal Timing Internal Clock Source Secondary Timing Normal CSU Timing Normal CSU Unit Menu Default IP AddressSubnet Mask Map Exchange Map Xchng Map In Use ABOFF Auto DS0 Map a and DS0 Map B Copy a B TempCreate Temp Review MAP AB Review Temp Edit TempApply Temp AB DSO Map Example Create Temp Selection Screen Port Configuration Port Config Nx56/64 Port Configuration Port Config Menu ItemsNx56/64 Menu Items Description DS0 Rate Data CTSDCD DSR Inband Mode Normal Mode of OperationTX CLK Source DBU Configuration Menu Items TSU 120e only Backup ModeBackup on Backup Delay Restore Delay Retry DelayBackup Testing Enable HR Disable HRDSX-1 Port Configuration Port Config Menu Items Yellow Alarm Signaling Line Length FTIN-BAND Loopback Utility Menu Complete Utility Menu Tree Factory Restore Fact Restore Time/DateSet Passcode If you want to Do this Unit ID Change/Set a PasscodePasscode Automatic Time-out No Passcode Desired CMD Mode Software Revision Software RevPort Utility Option Ports Enet Address TSU 120e only Utility Menu Test Menu Complete Test Menu Tree Network Tests Loopback TestsNetwork Interface Loopbacks Line Loopback Network Loopback Tests Activates the line loopback Test Patterns All Zeros All OnesQrss Pattern Terminates pattern generation Example Run Self-test Port Tests Port Test Menu Items for 0.1 Nx56/64 Loop is deactivated Cancel Tests DBU Loopback TSU 120e onlyDBU Test TSU 120e only DBU TST Result TSU 120e only Main Menu Telnet/Terminal Main Menu Status, Config, Util, and Test Menu Options DS0 Maps Configuration Menu Map Configuration Initializing the Temp MapIf you want to Use these selections Editing the Temp Map ExplanationApplying the Temp Map Reviewing Maps Remote Menu Access Management ConfigurationUnit Access Table Unit Access Table Add New Unit Default Unit Passcode Modify UnitDelete Unit Snmp Read Community Snmp Trap Community Host 1 Trap IP AddressHost 2 Trap IP Address Host 3 Trap IP Address Telnet/Terminal Timeout Telnet/Terminal PasswordSystem Location Auth. Fail Traps Sent Flash Download Quit Session About Snmp Basic ComponentsNetwork Manager Agent Commands MessagesGetRequest GetNextRequest TSU 120 Snmp Access Trap Snmp Trap Configuration Snmp MIB Browser Configuration Table A-1. How to Configure Network Manager MIB Snmp MIB Files Supported by the TSU Standard MIBs Adtran Enterprise-specific MIBsAdtran Product MIB ADTRAN.MIB Ftp.adtran.com Appendix B Understanding TR-08 Table B-1. Alarm Conditions FelpOOF TR-08 DS0 Conversion Table Table B-2.TR-08 DS0 Conversion TableDS0 TR-08 Channel Number Port Appendix B. Understanding TR-08 Wiring Network PinoutsConnections Table C-1. Network Pinouts Control In/Chain Table C-2. Control In/Chain in Pinout Chain Out Table C-3. Chain Out Pinout Connector type Part number Nx56/64 DTETable C-4. V.35 Pinout Nx56/64 DTE Connector type RJ-48C Table C-5. Pinout Connectors for Modular Jack InterfaceBase DSX-1 PBX Connector type Usoc 10BaseT TSU 120e onlyTable C-6 BaseT Ethernet TSU 120e only Pin Name to NIC Alarm Messages Network Interface NINx56/64 Interface Status Messages Following messages indicate the status of the Nx56/64 card Appendix D. System Messages Electrical Specifications T1/FT1 InterfaceCompatibility Nx56/64 V.35 Interface CTS, DCD, DSRDSX-1 Interface Chassis Specifications Management InterfacesChain In/Out Ports Option Slot Interface Environmental Specifications Input PowerFuse Operating Temperature Max Power Index Numerics GetNextRequest Snmp A-5 Index-4 61202129L1-1 Index-5 Index-6 61202129L1-1 Presales Inquiries and Applications Support Post-Sale SupportRepair and Return