Enviro EG28-120, EG28 DV owner manual Assemble the desired lengths of black pipe

Page 23
Roofing nails
Figure 30: Vertical Vent Termination Installation.

Initial Installation

QUALIFIED INSTALLERS ONLY

VERTICAL INSTALLATION:

1.Check the instructions for required clearances (air spaces) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafters, or other nearby combustible surfaces. Do not pack air spaces with insulation.

2. Set the gas appliance in the desired location.

 

Drop a plumb bob down from the ceiling to the

 

position of the appliance flue exit, and mark

 

the location where the vent will penetrate the

 

ceiling. Drill a small hole at this point. Next, drop

 

a plumb bob from the roof to the hole previously

 

drilled in the ceiling, mark the spot where the

 

vent will penetrate the roof. Determine if ceiling

 

joists, roof rafters, or other framing will obstruct

 

the venting system. You may wish to relocate

 

the appliance, or to offset, to avoid cutting load

 

bearing members.

 

3. To install the Round Support Box/Wall Thimble

 

in a flat ceiling, cut a 10 inch (25.4 cm) square

 

hole in the ceiling, centered in the hole drilled in

 

Step 2. Frame the hole as shown in Figure 29.

Figure 29: Wall Framing for 10” (25.4 cm) x 10” (25.4

4. Assemble the desired lengths of black pipe and

cm) Hole for Vertical Installation.

elbows necessary to reach from the appliance

 

adapter up through the Round Support Box. Insure that all pipe and elbow connections are in their fully twist-locked position.

5.Cut hole in the roof centered on the small hole placed in the roof from Step 2. The hole should be of sufficient size to meet minimum requirements for Clearance to Combustibles, as specified. Continue to assemble lengths of pipe and elbows necessary to reach from the ceiling support box up through the roof line. Galvanized pipe

and elbows

may be

utilized in

 

Vertical

the attic, as well as above the

 

Termination

 

 

roof line. The galvanized finish

Elbow Strap

Storm Collar

is desirable above the roof line,

 

 

due to the

higher

corrosion

 

Flashing

resistance.

 

 

 

 

 

 

 

6. Once the pipe sections have been joined, and run up through the hole in the roof, slip an elbow strap over the exposed sections, bend the support straps outwards, and push the elbow strap down to the roof level, as shown in Figure 30. Tighten the clamp around the pipe section. Use a level to make sure the pipe is truly vertical. With roofing nails, secure the

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents EG28 DV General Safety PrecautionsTable of Contents This Enviro EG28 DV Fireplace Codes And ApprovalsEG28 Exterior Dimensions SpecificationsOperating Instructions For Your Safety Read Completely Before OperatingPilot Burning Component Sound & ReasonRemoving the Door Maintenance and ServiceTurn the unit off, allow it to cool down completely Way, and snap into place Kit Parts ListConversion Kit Installation Removing valve Screw Must be not visibleQualified Installers only Initial InstallationCommon Vertical Installation Do not interfere with the structural integrity of the walls Vent Termination Restrictions KIT Components Assembly of Venting Kit Manufacturer Trade Name Nominal Sizes SV4EBR45 Vent restrictor ring End of the pipes and fittings, are Installing Vent Cap with Vinyl Siding Stand-Off Assemble the desired lengths of black pipe Use of Wall Straps Insulation Multi-Story Vent Pipe Installation33a-2002 Test Methods and the Resulting ITS/WH EG28 DV Wiring Diagram Max Supply Pressure Natural Gas Propane Main OrificeManifold Pressure Min. Manifold PressureLog Placement Secondary InstallationLog Placement with Embers Problem Possible Cause Solution Trouble ShootingReference Part Description Number Parts ListReference Number Part Description Part Number Parts Diagram Chassis EG 28 Gas Tray and Door Assemblies To the Dealer WarrantyWarranty Warranty Installation Data Sheet

EG28-120, EG28 DV specifications

The Enviro EG28 DV and EG28-120 are cutting-edge devices designed for enhancing environmental monitoring and improving overall efficiency in various applications. These units are part of Enviro's commitment to sustainable innovation, catering to industries such as agriculture, industrial processes, and smart cities.

One of the standout features of the Enviro EG28 DV is its advanced sensor technology. This device is equipped with high-precision sensors that can measure a range of environmental parameters, including air quality, temperature, humidity, and even soil metrics. The ability to gather diverse data points in real-time allows users to make informed decisions, ultimately leading to better resource management and environmental conservation.

The EG28-120 variant takes this a step further with its enhanced connectivity options. It supports various communication protocols, including Wi-Fi, Bluetooth, and cellular networks, ensuring seamless integration into existing systems. This connectivity not only facilitates remote monitoring but also enables data sharing across different platforms, making it easier for stakeholders to access crucial information and collaborate effectively.

Both models boast user-friendly interfaces, complete with intuitive dashboards that simplify data visualization. Users can easily track readings, analyze trends, and generate reports, which is essential for regulatory compliance and performance assessment. The devices are also complemented by mobile applications, allowing for on-the-go monitoring and alerts, thus promoting proactive management of environmental factors.

Durability is another critical aspect of the Enviro EG28 DV and EG28-120. Designed to withstand challenging conditions, these devices feature rugged exteriors and are resistant to dust and water, ensuring reliable performance in various environments. Their low power consumption is an added advantage, making them suitable for long-term deployment without frequent maintenance.

In summary, the Enviro EG28 DV and EG28-120 stand out for their advanced sensor capabilities, versatile connectivity, user-friendly design, and robust durability. These features make them invaluable tools for monitoring environmental conditions, supporting industries in their quest for sustainable practices and efficient resource management. With their innovative technologies, these devices are poised to play a significant role in shaping the future of environmental stewardship.
Top Page Image Contents