Stove will not shut down, Stove keeps going out

POTENTIOMETER READINGS:
Full clockwise (switched off) = open circuit, overload or infinite resistance
LOW FIRE	800K OHMS to	900K OHMS
HIGH FIRE	68K OHMS to	82K OHMS

-If the range does not vary or the switch does not close then replace the potentiometer.

8)The stove will not shut down

-Make sure the auto/manual switch is in the auto position.

-Check the connections to the 120°F (49°C)-N/O temperature sensor and the auto/manual switch against the wiring diagram.

-Check the 120°F (49°C)-N/O temperature sensor by removing one of the brown wires from the sensor. The unit should shut down right away as long as the switch is in the auto position, if this happens Replace the 120°F (49°C) –N/O sensor. If the stove does not shut down then test the switch.

-To test the switch, the stove must be cold. With one of the brown wires removed from the 120°F (49°C) N/O temperature sensor, remove the gray wire from the switch, the stove should shut down. If this is the result then replace the auto/manual switch.

-If the stove still does not shut off, replace the wiring harness.

9)The stove keeps going out

-If the stove goes out and leaves fresh unburned pellets in the burn pot liner, the fire is going out before the 120°F (49°C) –N/O temperature sensor shuts the stove off

-Check to see that the slider damper is in the correct position

-Turn the Dial-A-Fire up slightly (poor quality pellets will require a slightly higher setting)

-If the stove goes out and there are partially burned pellets or cigarette like ashes left in the burn pot liner, the stove shut down due to lack of air, exhaust temperature or a power failure.

-Adjust the slider damper

-Check to see if the stove needs a more thorough cleaning.

-Turn the Dial-A-Fire up slightly

-Did the power go out?

-If the stove goes out and there are no pellets in the burn pot liner, the auger is stopping.

-SEE: “The auger motor will not function normally” and “The exhaust blower will not function normally”.

10)Ignitor will not function normally.

-Everything else in the stove operates but the ignitor will not light the pellets.

-Make sure the burn pot liner is tight against the ignitor tube.

-Check all the electrical connections to the 120°F (49°C) temperature sensor located on the exhaust channel

-Check the connections at the igniter socket.

-Place a jumper wire between the two leads on the 120°F (49°C) temperature sensor. If the igniter works. Replace the sensor

-If the igniter does not work. Replace the igniter.

NOTE: The igniter should be a bright yellow or bright orange in color. If not Replace the igniter.

EF-II I specifications

The Enviro EF-II I represents a significant advancement in eco-friendly filtration technology, designed to meet the demands of a rapidly changing environment. Focusing on high-efficiency performance and sustainability, the EF-II I offers an innovative approach to air and water purification, making it a vital tool for both residential and commercial applications.

One of the key features of the Enviro EF-II I is its multi-stage filtration system. This system incorporates pre-filters, HEPA filters, and activated carbon filters, which work in concert to capture a wide range of pollutants, allergens, and harmful particles. The pre-filters are designed to trap larger particles, while HEPA technology ensures that up to 99.97% of airborne contaminants down to 0.3 microns are effectively removed. The activated carbon filter then targets volatile organic compounds (VOCs) and odors, resulting in cleaner, fresher air.

In addition to its robust filtration capabilities, the EF-II I is equipped with advanced sensing technology. The built-in smart sensors continuously monitor air quality and provide real-time feedback to users. The unit can adjust its performance based on current air conditions, optimizing energy use and enhancing overall efficiency. This responsive technology not only ensures a healthier indoor environment but also contributes to energy savings.

The design of the Enviro EF-II I emphasizes user-friendliness. An intuitive interface with easy-to-read displays allows users to monitor filter life, check air quality levels, and adjust settings with minimal hassle. Moreover, a smart app compatibility feature means users can control the device remotely, receiving alerts and notifications straight to their smartphones.

Another notable characteristic of the EF-II I is its eco-friendly construction. Made from sustainable materials, the device is built to last while minimizing environmental impact. The filters themselves are replaceable and recyclable, aligning with a commitment to reduce waste.

Noise reduction technology ensures that the EF-II I operates quietly, making it suitable for various environments, from homes to offices. This emphasis on a peaceful atmosphere, combined with the effectiveness of its filtration system, underscores the Enviro EF-II I's position as a leader in air and water purification technology.

In summary, the Enviro EF-II I merges state-of-the-art filtration technology with smart features and sustainable design, making it an essential solution for those seeking cleaner air and healthier living spaces. Its combination of efficiency, user-friendly operation, and environmental consciousness sets a new standard in the industry, catering to the needs of a modern, health-focused society.