Enviro EF-II I Deciding Where to Locate Your Pellet Appliance, Vent Termination Requirements

Page 12

DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE

1.Check clearances to combustibles.

2.Do not obtain combustion air from an attic, garage or any unventilated space. Combustion air may be obtained from a ventilated crawlspace.

3.Do not install the stove in a bedroom.

4.You can vent the stove through an exterior wall behind the unit or connect it to an existing masonry or metal chimney (must be lined if the chimney is over 6” in diameter, or less than 28 sq. inches cross sectional area). An interior vent can be used with approved pipe passing through the ceiling and roof.

5.Locate the stove in a large and open room that is centrally located in the house. This will optimize heat circulation.

6.The power cord is 8 feet (2.43 m) long and may require a grounded extension cord to reach

the nearest electrical outlet.

VENT TERMINATION REQUIREMENTS

A)Do not terminate the vent in any enclosed or semi-enclosed areas, such as a carport, garage, attic, crawl space, narrow walkway, closely fenced area, under a sundeck or porch, or any location that can build up a concentration of fumes such as stairwells, covered breezeway, etc.

B)Vent surfaces can become hot enough to cause burns if touched by children. Non-combustible shielding r guards may be required.

C)Termination must exhaust above inlet elevation. It is recommended that at least five feet of vertical pipe be installed when the appliance is vented directly through a wall to create some natural draft. This is to prevent the possibility of smoke or odor during appliance shut down and to keep exhaust from causing a nuisance or hazard from exposing people or shrubs to high temperatures. In any case, the safest and preferred venting method is to extend the vent through the roof.

D)The vent terminal cannot be:

-Less than 4 feet (1.2 m) below

-Less than 4 feet (1.2 m) horizontally from, and

-Less than 1 foot (30 cm) above doors, window openings, or gravity /ventilation air inlets into the building.

E)Distance from bottom termination and grade –12” (305 mm) minimum. This is conditional upon the plants and nature of grade surface. The exhaust gases are hot enough to ignite grass, plants and shrubs that are located in the vicinity of termination. The grade surface must not be lawn. Distance from bottom of termination and public walkways is 7 feet (2.1 m) minimum.

F)Distance to combustible materials is 2 feet (610 mm). This includes adjacent buildings, fences, protruding arts of the structure, roof overhang, plants, shrubs, etc.

G)When installing an FPI or BIH the chimney must be fully lined. Unless the chimneys inside diameter are less than 6” around or has a cross section area of less than 28 square inches. We strongly recommend lining all masonry chimneys

H)If the unit is incorrectly vented or the air to fuel mixture is out of balance, a slight discoloration of the exterior of the house might occur. Since these factors are beyond Sherwood Industries Ltd. Control, we grant no guarantee against such incidents.

IT IS RECOMMENDED THAT ONLY AN AUTHORIZED DEALER INSTALL YOUR PELLET STOVE

12

Image 12
Contents EF-ΙΙ Envirofire Installation Manual InstallationImportant Safety Data USE of Cordwood is Prohibited by LAWPellet Quality is Important Please Read the Following Automatic Safety Features of Your Pellet Stove HOW to Start Your Pellet Appliance Turning Your Pellet Appliance OFFSLIDER/DAMPER Installation /OPERATIONS Instructions On LOWPush all Way On HighAreas for Routine Inspection ASH PAN and Door GasketsFreestanding ASH PAN Blower MechanismsPost Season CLEAN-UP Door GlassFresh AIR Intake Inside FireboxElectrical Component Functions 10 F 71C Temperature Sensor 11 F 49C- N/O Temperature Sensor Shut Down Sensor12 F 49C-N/C Temperature Sensor Igniter Shut Down Sensor Vacuum SwitchDeciding Where to Locate Your Pellet Appliance Vent Termination RequirementsDimensions Removing Your NEW Stove from IT’S PalletMasonry Fireplace Insert INSTALLATION, Model FPI Fireplace Insert SizeAssembling the Face Plate for the FPI and BIH Models Recommended Framing for Built in Heater Built in Heater Clearances to CombustiblesClearances to Combustibles Clearance to Combustibles FreestandingModel FS Freestanding Installation Installation KeyholesHorizontal Exhaust Through the Wall Through Wall Installation Inside Vertical INSTALLATION, Model FS Outside Vertical Pipe Installation Mobile Home Installation Outside Fresh AIR ConnectionsTroubleshooting TroubleshootingDo not Stove will not startStove will not function in the Auto mode when hot Exhaust blower will not function normallyConvection blower will not function normally Auger motor will not function normallyStove will not shut down Stove keeps going outIgnitor will not function normally Wiring Diagram Parts List EF-146 EF-079July Exploded Components Warranty To the DealerTo the Distributor For the do-it-yourself Individual

EF-II I specifications

The Enviro EF-II I represents a significant advancement in eco-friendly filtration technology, designed to meet the demands of a rapidly changing environment. Focusing on high-efficiency performance and sustainability, the EF-II I offers an innovative approach to air and water purification, making it a vital tool for both residential and commercial applications.

One of the key features of the Enviro EF-II I is its multi-stage filtration system. This system incorporates pre-filters, HEPA filters, and activated carbon filters, which work in concert to capture a wide range of pollutants, allergens, and harmful particles. The pre-filters are designed to trap larger particles, while HEPA technology ensures that up to 99.97% of airborne contaminants down to 0.3 microns are effectively removed. The activated carbon filter then targets volatile organic compounds (VOCs) and odors, resulting in cleaner, fresher air.

In addition to its robust filtration capabilities, the EF-II I is equipped with advanced sensing technology. The built-in smart sensors continuously monitor air quality and provide real-time feedback to users. The unit can adjust its performance based on current air conditions, optimizing energy use and enhancing overall efficiency. This responsive technology not only ensures a healthier indoor environment but also contributes to energy savings.

The design of the Enviro EF-II I emphasizes user-friendliness. An intuitive interface with easy-to-read displays allows users to monitor filter life, check air quality levels, and adjust settings with minimal hassle. Moreover, a smart app compatibility feature means users can control the device remotely, receiving alerts and notifications straight to their smartphones.

Another notable characteristic of the EF-II I is its eco-friendly construction. Made from sustainable materials, the device is built to last while minimizing environmental impact. The filters themselves are replaceable and recyclable, aligning with a commitment to reduce waste.

Noise reduction technology ensures that the EF-II I operates quietly, making it suitable for various environments, from homes to offices. This emphasis on a peaceful atmosphere, combined with the effectiveness of its filtration system, underscores the Enviro EF-II I's position as a leader in air and water purification technology.

In summary, the Enviro EF-II I merges state-of-the-art filtration technology with smart features and sustainable design, making it an essential solution for those seeking cleaner air and healthier living spaces. Its combination of efficiency, user-friendly operation, and environmental consciousness sets a new standard in the industry, catering to the needs of a modern, health-focused society.