Enviro EF-II I SLIDER/DAMPER Installation /OPERATIONS Instructions, On LOW, Push all Way, On High

Page 7

SLIDER/DAMPER INSTALLATION /OPERATIONS INSTRUCTIONS

This is used to regulate the airflow through the pellet stove.

INSTALLATION:

1.Remove the slider rod (short rod with knob and nuts) and the two nuts from their package and open the left side panel. This is the smaller of the two rods. Remove the knob from the knob.

2.Remove the knob and the outer nut from the rod. Push the rod through the hole in the slider. Place the other nut on the rod and tighten, leaving a 1/32” gap between the slider and one of the other nuts.

3.Make sure the slider moves freely. Close the left side panel and the tighten screws. Push the rod through the hole in the side panel. Screw the knob on to the slider rod.

OPERATION:

1.On the low heat output settings, push the slider all the way in.

2.On the high heat output pull the slider out until a good fire is achieved. A good fire is in between a fire with lazy flames (black tipped flames) and a forced fire (very quick, shorter flames). A good fire is the most efficient and will have a bright and active flame.

3.Hot magnehelic reading 0.10--0.12

ON LOW

Push all the

way in

ON HIGH

Pull out until an efficient flame is achieved

THE SCRAPER ROD: Push the stainless steel rod through the hole in the heat exchanger, thread the rod into the scraper plate.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents EF-ΙΙ Installation Envirofire Installation ManualUSE of Cordwood is Prohibited by LAW Important Safety DataPellet Quality is Important Please Read the Following Automatic Safety Features of Your Pellet Stove Turning Your Pellet Appliance OFF HOW to Start Your Pellet ApplianceOn High SLIDER/DAMPER Installation /OPERATIONS InstructionsOn LOW Push all WayBlower Mechanisms Areas for Routine InspectionASH PAN and Door Gaskets Freestanding ASH PANInside Firebox Post Season CLEAN-UPDoor Glass Fresh AIR IntakeElectrical Component Functions Vacuum Switch 10 F 71C Temperature Sensor11 F 49C- N/O Temperature Sensor Shut Down Sensor 12 F 49C-N/C Temperature Sensor Igniter Shut Down SensorVent Termination Requirements Deciding Where to Locate Your Pellet ApplianceRemoving Your NEW Stove from IT’S Pallet DimensionsFireplace Insert Size Masonry Fireplace Insert INSTALLATION, Model FPIAssembling the Face Plate for the FPI and BIH Models Built in Heater Clearances to Combustibles Recommended Framing for Built in HeaterClearance to Combustibles Freestanding Clearances to CombustiblesInstallation Keyholes Model FS Freestanding InstallationHorizontal Exhaust Through the Wall Through Wall Installation Inside Vertical INSTALLATION, Model FS Outside Vertical Pipe Installation Outside Fresh AIR Connections Mobile Home InstallationStove will not start TroubleshootingTroubleshooting Do notAuger motor will not function normally Stove will not function in the Auto mode when hotExhaust blower will not function normally Convection blower will not function normallyStove keeps going out Stove will not shut downIgnitor will not function normally Wiring Diagram Parts List EF-079 EF-146July Exploded Components For the do-it-yourself Individual WarrantyTo the Dealer To the Distributor

EF-II I specifications

The Enviro EF-II I represents a significant advancement in eco-friendly filtration technology, designed to meet the demands of a rapidly changing environment. Focusing on high-efficiency performance and sustainability, the EF-II I offers an innovative approach to air and water purification, making it a vital tool for both residential and commercial applications.

One of the key features of the Enviro EF-II I is its multi-stage filtration system. This system incorporates pre-filters, HEPA filters, and activated carbon filters, which work in concert to capture a wide range of pollutants, allergens, and harmful particles. The pre-filters are designed to trap larger particles, while HEPA technology ensures that up to 99.97% of airborne contaminants down to 0.3 microns are effectively removed. The activated carbon filter then targets volatile organic compounds (VOCs) and odors, resulting in cleaner, fresher air.

In addition to its robust filtration capabilities, the EF-II I is equipped with advanced sensing technology. The built-in smart sensors continuously monitor air quality and provide real-time feedback to users. The unit can adjust its performance based on current air conditions, optimizing energy use and enhancing overall efficiency. This responsive technology not only ensures a healthier indoor environment but also contributes to energy savings.

The design of the Enviro EF-II I emphasizes user-friendliness. An intuitive interface with easy-to-read displays allows users to monitor filter life, check air quality levels, and adjust settings with minimal hassle. Moreover, a smart app compatibility feature means users can control the device remotely, receiving alerts and notifications straight to their smartphones.

Another notable characteristic of the EF-II I is its eco-friendly construction. Made from sustainable materials, the device is built to last while minimizing environmental impact. The filters themselves are replaceable and recyclable, aligning with a commitment to reduce waste.

Noise reduction technology ensures that the EF-II I operates quietly, making it suitable for various environments, from homes to offices. This emphasis on a peaceful atmosphere, combined with the effectiveness of its filtration system, underscores the Enviro EF-II I's position as a leader in air and water purification technology.

In summary, the Enviro EF-II I merges state-of-the-art filtration technology with smart features and sustainable design, making it an essential solution for those seeking cleaner air and healthier living spaces. Its combination of efficiency, user-friendly operation, and environmental consciousness sets a new standard in the industry, catering to the needs of a modern, health-focused society.
Top Page Image Contents