Enviro EF-II I technical manual Stove will not function in the Auto mode when hot

Page 25

3)The stove will not function in the “AUTO” mode when hot

-If the unit fails to operate, by-pass the auto side of the switch by inserting a jumper wire between the dual black wires and the dual brown wires located on the back of the switch. Plug the stove back in. if the stove operates , Replace the switch.

4)The exhaust blower will not function normally

-Open the left side panel, check all connections against the wiring diagram.

-If all the connections are verified and the exhaust blower does not function at all , tap lightly on the exhaust motors end cap, this may loosen a tight motor.

-Apply 115V AC directly to the exhaust blower. If the motor does not run, replace the blower.

-If the motor runs, have your dealer inspect the wiring harness

5)The convection blower will not function normally

-Check all of the connections between the fan controller, switch, and the convection blower against the wiring diagram.

If the convection blower will not operate, Apply 115V AC to the motor directly, If the motor runs, Replace the fan controller. If the motor does not run, the convection blower has failed. Replace the blower.

6)the auger motor will not function normally

-Make sure the exhaust blower is operating.

-Make sure the Dial-A-Fire is turned on.

-Unplug the stove and open the side and back panels.

-Check all the connections to the auger motor, Dail-A-Fire, Vacuum sensor, 200°F (93°C) temperature sensor and the timing control module against the wiring diagram in this manual.

-Check the condition of the Vacuum hose (located on the left-hand side of the stove). It should not be cracked or torn and should be installed on the top air inlet tube of the sensor.

-Check the manual reset button on the 200°F (93°C) temperature sensor. If this sensor has been tripped check the cause of the over-heating before pushing the red button in. check the auger for movement.

-If the auger still does not operate then apply 115V AC directly to the auger motor. If the auger motor does not work. Replace the auger motor.

-By-pass the 200°F (93°C) temperature sensor with a jumper wire, check the auger. If the auger works replace the 200°F (93°C) sensor.

-Check the voltage across the load pins of the timing module. It should be around 1-2 VAC, cycling to line voltage during an auger pulse. If not, replace the timing control module.

-Check the Vacuum sensor by placing a jumper wire between the Blue and Black wires that are attached to the sensor. If the auger works, test to see if the exhaust blower is producing enough vacuum.

-To test the exhaust vacuum place a magnehelic gauge in the sensor end of the vacuum tube. It should read over 0.5. if the reading is good then replace the vacuum sensor.

-If the auger motor still does not work, then attempt to by-pass the auger Dial-A-Fire control by removing the leads from the timing control module’s second delay pins and placing a jumper wire across the pins. If the auger now cycles very quickly, test the Dial-A-Fire potentiometer. If the auger did not then replace the timing control module.

-To test the Dial-A-Fire potentiometer, place the two test leads from a multimeter into the leads of the potentiometer. The potentiometer should have a range of 68k OHMS to approximately 850k OHMS (plus or minus 10%). If the range is not close then replace the potentiometer.

7)The Dial-A-Fire has no effect on the fire

-Make sure that all connections to the timer control module are correct and secure.

-Perform a resistance test to the Dial-A-Fire potentiometer, by placing the two leads from a multimeter into

the two leads of the potentiometer. The potentiometer should have a range of 68k to 850k OHMS (plus or minus 10%)

-

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents EF-ΙΙ Installation Envirofire Installation ManualUSE of Cordwood is Prohibited by LAW Important Safety DataPellet Quality is Important Please Read the Following Automatic Safety Features of Your Pellet Stove Turning Your Pellet Appliance OFF HOW to Start Your Pellet ApplianceOn LOW SLIDER/DAMPER Installation /OPERATIONS InstructionsPush all Way On HighASH PAN and Door Gaskets Areas for Routine InspectionFreestanding ASH PAN Blower MechanismsDoor Glass Post Season CLEAN-UPFresh AIR Intake Inside FireboxElectrical Component Functions 11 F 49C- N/O Temperature Sensor Shut Down Sensor 10 F 71C Temperature Sensor12 F 49C-N/C Temperature Sensor Igniter Shut Down Sensor Vacuum SwitchVent Termination Requirements Deciding Where to Locate Your Pellet ApplianceRemoving Your NEW Stove from IT’S Pallet DimensionsFireplace Insert Size Masonry Fireplace Insert INSTALLATION, Model FPIAssembling the Face Plate for the FPI and BIH Models Built in Heater Clearances to Combustibles Recommended Framing for Built in HeaterClearance to Combustibles Freestanding Clearances to CombustiblesInstallation Keyholes Model FS Freestanding InstallationHorizontal Exhaust Through the Wall Through Wall Installation Inside Vertical INSTALLATION, Model FS Outside Vertical Pipe Installation Outside Fresh AIR Connections Mobile Home InstallationTroubleshooting TroubleshootingDo not Stove will not startExhaust blower will not function normally Stove will not function in the Auto mode when hotConvection blower will not function normally Auger motor will not function normallyStove keeps going out Stove will not shut downIgnitor will not function normally Wiring Diagram Parts List EF-079 EF-146July Exploded Components To the Dealer WarrantyTo the Distributor For the do-it-yourself Individual

EF-II I specifications

The Enviro EF-II I represents a significant advancement in eco-friendly filtration technology, designed to meet the demands of a rapidly changing environment. Focusing on high-efficiency performance and sustainability, the EF-II I offers an innovative approach to air and water purification, making it a vital tool for both residential and commercial applications.

One of the key features of the Enviro EF-II I is its multi-stage filtration system. This system incorporates pre-filters, HEPA filters, and activated carbon filters, which work in concert to capture a wide range of pollutants, allergens, and harmful particles. The pre-filters are designed to trap larger particles, while HEPA technology ensures that up to 99.97% of airborne contaminants down to 0.3 microns are effectively removed. The activated carbon filter then targets volatile organic compounds (VOCs) and odors, resulting in cleaner, fresher air.

In addition to its robust filtration capabilities, the EF-II I is equipped with advanced sensing technology. The built-in smart sensors continuously monitor air quality and provide real-time feedback to users. The unit can adjust its performance based on current air conditions, optimizing energy use and enhancing overall efficiency. This responsive technology not only ensures a healthier indoor environment but also contributes to energy savings.

The design of the Enviro EF-II I emphasizes user-friendliness. An intuitive interface with easy-to-read displays allows users to monitor filter life, check air quality levels, and adjust settings with minimal hassle. Moreover, a smart app compatibility feature means users can control the device remotely, receiving alerts and notifications straight to their smartphones.

Another notable characteristic of the EF-II I is its eco-friendly construction. Made from sustainable materials, the device is built to last while minimizing environmental impact. The filters themselves are replaceable and recyclable, aligning with a commitment to reduce waste.

Noise reduction technology ensures that the EF-II I operates quietly, making it suitable for various environments, from homes to offices. This emphasis on a peaceful atmosphere, combined with the effectiveness of its filtration system, underscores the Enviro EF-II I's position as a leader in air and water purification technology.

In summary, the Enviro EF-II I merges state-of-the-art filtration technology with smart features and sustainable design, making it an essential solution for those seeking cleaner air and healthier living spaces. Its combination of efficiency, user-friendly operation, and environmental consciousness sets a new standard in the industry, catering to the needs of a modern, health-focused society.
Top Page Image Contents