Enviro 50-1386 instruction

Installation

SLIDER/DAMPER SETTING:

This is used to regulate the airflow through the pellet stove.

THE SLIDER / DAMPER MUST BE SET AT TIME OF INSTALLATION.

A Qualified Service Technician or Installer must set the Slider Damper.

The slider damper is located behind the cast doors and under the firebox.

•If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the Slider Damper should be moved to the left slightl, lessen the air flow into the firebox.

•If, after long periods of burning, the fire builds up and overflows the burn pot or there is a build up of clinkers, this would be a sign that the pellet quality is poor, this requires more primary air, the slider damper must be moved to the right to give the fire more air.

Less Air

More Air

Figure 15: Slider / damper positions.

The easiest way to make sure that an efficient flame is achieved is to understand the characteristics of the fire.

• A tall, lazy flame with dark orange tips requires more air – Push Right

• A short, brisk flame, like a blowtorch, has too much air – Push Left

• If the flame is in the middle of these two characteristics with a bright yellow/orange, active flame with no black tips then the air is set for proper operation.

The combustion exhaust blower is a variable speed blower controlled by the heat output setting. This blower will increse or decrease the blower speed as the heat output setting is turned up or down.

Figure 16: Efficient Flame.

SPECIAL NOTES:

Pellet quality is a major factor in how the pellet stove will operate. If the pellets have a high moisture content or ash content the fire will be less efficient and has a higher possibility of the fire building up and creating clinkers (hard ash build-up). If this happens, move the Slider / Damper to the right slightly to increase the air flow to the fire.

Taking a reading of vacuum pressure inside the firebox with a magnehelic gauge can be used to set the slider for best combustion. The best settings are a reading of 0.12 to 0.13 inches of water column (30 Pa) on the high fire setting. Some fuels may require higher or lower settings. The reading can be taken from the 1⁄8” (3 mm) hole located on the front of the unit below the door in the ash pan front.

50-1386 specifications

Enviro 50-1386 is an advanced product designed for individuals and organizations seeking a sustainable and efficient solution to environmental challenges. Renowned for its eco-friendly attributes, Enviro 50-1386 marries cutting-edge technology with innovative design, making it suitable for a variety of applications in climate management, waste reduction, and resource optimization.

One of the standout features of Enviro 50-1386 is its superior energy efficiency. This product incorporates state-of-the-art technologies that minimize energy consumption while maximizing performance. The utilization of renewable energy sources further enhances its appeal, aligning with global goals for sustainability and environmental conservation.

Enviro 50-1386 utilizes smart sensor technology that allows for real-time monitoring and adjustments. These sensors can detect changes in environmental conditions, such as temperature, humidity, and air quality, and respond accordingly. This intelligent capability means that users can maintain optimal operating conditions with minimal manual intervention, significantly reducing human error and the need for constant oversight.

Moreover, the product's user-friendly interface makes it accessible for a wide range of users, from environmental professionals to everyday consumers. The intuitive design allows users to interact with the device seamlessly, facilitating a better understanding of environmental metrics and enhancing data-driven decision-making.

Durability is another characteristic of the Enviro 50-1386. Constructed from high-quality materials, it is designed to withstand various environmental stresses, ensuring a long service life. This resilience not only reduces the need for frequent replacements but also contributes to a less wasteful lifecycle.

In addition to being environmentally conscious, Enviro 50-1386 is versatile. It can be adapted for use in multiple sectors, including agriculture, manufacturing, and urban infrastructure. This adaptability makes it an essential tool for organizations seeking to enhance their sustainability credentials while also improving efficiency.

Overall, Enviro 50-1386 is a testament to how technology can be aligned with ecological principles, offering users a powerful tool to meet their environmental objectives while promoting a sustainable future. Whether for individual use or integrated into larger systems, Enviro 50-1386 stands at the forefront of the green technology movement.