Masonry fireplace positive flue installation

Installation

POSITIVE FLUE CONNECTION WITHOUT A FULL RELINE (USA ONLY):

This unit does not require a full reline (in USA only) when installing into a masonry fireplace, however, it is recommended to ensure proper drafting of the appliance.

IMPORTANT: Ensure the chimney and firebox are cleaned and free of all debris, including soot and ashes, before proceeding with this installation. If it is not clean soot maybe blown into the room through the unit’s blower. Ensure the fireplace and chimney have not deteriorated in any way. If there is any sign of corrosion or damage in the chimney the unit can not be installed. This unit can be installing in a masonry fireplace built to (UBC 37 or ULC S628 standards) or a factory built fireplace (built to UL 127 or ULC S610 standards).

1.If installing the Empress with a skirt, the skirt must be installed before the installation.

2.Install the hearth pad. The floor 6” (150 mm) in front of the unit and 6” (150 mm) to each side of the unit must be protected with a non-combustible hearth pad.

3.The vent connector from the insert must extend a minimum of 18” above the chimney seal plate. The chimney seal plate area must be sealed to prevent the exhaust from the chimney from coming

Top of vent pipe

must be 18"

(45.7cm) minimum above the chimney seal plate.

Optional

Exhaust Starter

Elbow (or Exhaust

Starter with Clean-out Tee).

The existing chimney can

not be corroded or

damaged in any way.

Chimney must be completely sealed with a non-combustible material and maybe removed annually for cleaning.

12" (30.5cm) Mantle Minimum 36" (91 cm) from Bottom of stove.

Surround Panel

Min 6" (15.2 cm)

Floor Protection

back into the fireplace and prevent air from the fireplace from entering the chimney which will affect proper drafting of appliance.

A qualified installer should evaluate the existing fireplace to determine the best method for achieving a positive flue connection between the vent pipe or liner and the chimney. Whatever method used must effectively seal the area to prevent room air passage to the chimney cavity of the fireplace. A couple examples of Approved Methods of Achieving a Positive Flue Connection are:

a)Secure a seal-off plate (i.e. 22- gage sheet steel) in the masonry fireplace throat using masonry screws.

b)Pack non-combustible material (i.e. rockwool) around the vent pipe or using a flue adapter.

4.Set leveling leg to approximate height.

5.Connect the Exhaust Starter Quick Connect, straight or elbow, to the exhaust pipe.

��

Figure 7: Masonry fireplace positive flue installation.

IMPORTANT: The chimney seal plate must be removed for the annually chimney cleaning as ash will build up on top of the plate.

50-1386 specifications

Enviro 50-1386 is an advanced product designed for individuals and organizations seeking a sustainable and efficient solution to environmental challenges. Renowned for its eco-friendly attributes, Enviro 50-1386 marries cutting-edge technology with innovative design, making it suitable for a variety of applications in climate management, waste reduction, and resource optimization.

One of the standout features of Enviro 50-1386 is its superior energy efficiency. This product incorporates state-of-the-art technologies that minimize energy consumption while maximizing performance. The utilization of renewable energy sources further enhances its appeal, aligning with global goals for sustainability and environmental conservation.

Enviro 50-1386 utilizes smart sensor technology that allows for real-time monitoring and adjustments. These sensors can detect changes in environmental conditions, such as temperature, humidity, and air quality, and respond accordingly. This intelligent capability means that users can maintain optimal operating conditions with minimal manual intervention, significantly reducing human error and the need for constant oversight.

Moreover, the product's user-friendly interface makes it accessible for a wide range of users, from environmental professionals to everyday consumers. The intuitive design allows users to interact with the device seamlessly, facilitating a better understanding of environmental metrics and enhancing data-driven decision-making.

Durability is another characteristic of the Enviro 50-1386. Constructed from high-quality materials, it is designed to withstand various environmental stresses, ensuring a long service life. This resilience not only reduces the need for frequent replacements but also contributes to a less wasteful lifecycle.

In addition to being environmentally conscious, Enviro 50-1386 is versatile. It can be adapted for use in multiple sectors, including agriculture, manufacturing, and urban infrastructure. This adaptability makes it an essential tool for organizations seeking to enhance their sustainability credentials while also improving efficiency.

Overall, Enviro 50-1386 is a testament to how technology can be aligned with ecological principles, offering users a powerful tool to meet their environmental objectives while promoting a sustainable future. Whether for individual use or integrated into larger systems, Enviro 50-1386 stands at the forefront of the green technology movement.