Enviro 50-1386 technical manual Automatic Safety Features

Page 4

Introduction

ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should be connected to a standard 120 volts, 60 hertz electrical outlet and also must be accessible. If this power cord should become damaged, a replacement power cord must be purchased from the manufacturer or a qualified ENVIRO dealer. Be careful that the electrical cord is not trapped under the appliance and that it is clear of any hot surfaces or sharp edges. This unit’s maximum power requirement is (4.1 Amps) 500 watts.

GLASS: Do not abuse the glass by striking or slamming the door. Do not attempt to operate the stove with broken glass. The stove uses ceramic glass. Replacement glass must be purchased from an ENVIRO dealer. Do not attempt to open the door and clean the glass while the unit is in operation or if glass is hot. To clean the glass, use a soft cotton cloth and mild window cleaner, gas or wood stove glass cleaner, or take a damp paper towel and dip into the fly ash. This is a very mild abrasive and will not damage the glass.

SMOKE DETECTOR: Smoke detectors should be installed and maintained in the structure when installing and operating a pellet burning appliance.

OPERATION: The ash pan and door must be closed securely for proper and safe operation of the pellet stove. Also ensure all gaskets on the door are checked and replaced when necessary.

INSTALLATION: Be sure to maintain the structural integrity of your home when passing a vent through walls, ceilings, or roofs. It is recommended that the unit be secured into its position in order to avoid any displacement.

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

FRESH AIR: Outside Fresh Air is optional. Consider all large air moving devices when installing your unit and provide room air accordingly. Limited air for combustion may result in poor performance, smoking and other side effects of poor combustion.

If you have any questions with regards to your stove or the above-mentioned information, please feel free to contact your local dealer for further clarification and comments.

SINCE SHERWOOD INDUSTRIES LTD. HAS NO CONTROL OVER THE INSTALLATION OF YOUR STOVE, SHERWOOD INDUSTRIES LTD. GRANTS NO WARRANTY IMPLIED OR STATED FOR THE INSTALLATION OR MAINTENANCE OF YOUR STOVE. THEREFORE, SHERWOOD INDUSTRIES LTD. ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

AUTOMATIC SAFETY FEATURES:

Your pellet Stove has the following safety features:

A)The stove will shut off when the fire goes out and the exhaust temperature drops below 120 °F (49°C).

B)The stove has a high temperature safety switch. If the temperature on the hopper reaches 200 °F (93 °C) the auger will automatically stop and you will get a #2 flash code, and the stove will shut off when the exhaust temperature cools. If this happens call your local dealer to reset the 200 °F (93 °C) high limit switch. FIND THE REASONS WHY THE UNIT OVERHEATED.

C)The unit is equipped with a vacuum switch to monitor the venting and the build up of ash in the burn pot; if either becomes blocked the vacuum switch will turn off the auger and the stove will shut off.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Empress Table of Contents Introduction Automatic Safety Features Installation DimensionsRefer to Figure Side wall to center of unit Inches If installing Empress With a skirt Masonry fireplace positive flue installation Screws to move hopper Removal Slider / Damper Must be SET AT Time of Installation Stove will not operate when hot TroubleshootingStove will not start Exhaust motor will not function normally Light # 2 on Heat output bar flashingControl settings Heat Level has no effect on the fire Convection blower will not function normallyIgnitor- the pellets will not light Stove keeps going outWiring Diagram Parts List Reference Description Part NumberParts List Parts Diagram Components Parts Diagram Parts To the Dealer WarrantyTo the Distributor Exclusions and Limitations Warranty Installation Data Sheet Name of Owner Address

50-1386 specifications

Enviro 50-1386 is an advanced product designed for individuals and organizations seeking a sustainable and efficient solution to environmental challenges. Renowned for its eco-friendly attributes, Enviro 50-1386 marries cutting-edge technology with innovative design, making it suitable for a variety of applications in climate management, waste reduction, and resource optimization.

One of the standout features of Enviro 50-1386 is its superior energy efficiency. This product incorporates state-of-the-art technologies that minimize energy consumption while maximizing performance. The utilization of renewable energy sources further enhances its appeal, aligning with global goals for sustainability and environmental conservation.

Enviro 50-1386 utilizes smart sensor technology that allows for real-time monitoring and adjustments. These sensors can detect changes in environmental conditions, such as temperature, humidity, and air quality, and respond accordingly. This intelligent capability means that users can maintain optimal operating conditions with minimal manual intervention, significantly reducing human error and the need for constant oversight.

Moreover, the product's user-friendly interface makes it accessible for a wide range of users, from environmental professionals to everyday consumers. The intuitive design allows users to interact with the device seamlessly, facilitating a better understanding of environmental metrics and enhancing data-driven decision-making.

Durability is another characteristic of the Enviro 50-1386. Constructed from high-quality materials, it is designed to withstand various environmental stresses, ensuring a long service life. This resilience not only reduces the need for frequent replacements but also contributes to a less wasteful lifecycle.

In addition to being environmentally conscious, Enviro 50-1386 is versatile. It can be adapted for use in multiple sectors, including agriculture, manufacturing, and urban infrastructure. This adaptability makes it an essential tool for organizations seeking to enhance their sustainability credentials while also improving efficiency.

Overall, Enviro 50-1386 is a testament to how technology can be aligned with ecological principles, offering users a powerful tool to meet their environmental objectives while promoting a sustainable future. Whether for individual use or integrated into larger systems, Enviro 50-1386 stands at the forefront of the green technology movement.
Top Page Image Contents