Enviro 50-1386 technical manual Screws to move hopper

Page 9

Installation

ADJUSTING HOPPER HEIGHT:

The back height of this unit can be set to one (1) of three (3) heights; 1913/16” (503 mm), 2013/16” (529 mm), 2113/16” (554 mm). The hopper should be set to the maximum height that can be used in the installation.

To change the height of the hopper up or down, remove the seven (7) T-20 screws, three (3) on each side and one (1) on the back. The screw placement is shown Figure 8. Move the hopper assembly to the required setting and replace the screws. When the hopper back is in place it is recommended that silicone is used to seal the bottom lip of the hopper back and sides.

Figure 8: Screws to move hopper.

INSTALLATION OF CAST SKIRT OPTION:

The cast skirt is a five (5) piece option that can be installed when the front of the Empress FPI is going to be lower then the back of the unit; ensure that none are damaged before you proceed.

Figure 10: Installing Cast Skirt.

Figure 9: Assembling Cast Skirt.

1.Using a 3⁄8” socket or wrench connect the five (5) pieces of the skirt together with four (4) screws provided (see Figure 9). Do not completely tighten the screws; the screws should be loose enough that the cast pieces will be able to be adjusted but notfall apart.

2.Gently put the Empress FPI on its back.

3.Using two (2) screws provided attach the cast skirt to the bottom of the unit as shown in Figure 10.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Empress Table of Contents Introduction Automatic Safety Features Dimensions InstallationRefer to Figure Side wall to center of unit Inches If installing Empress With a skirt Masonry fireplace positive flue installation Screws to move hopper Removal Slider / Damper Must be SET AT Time of Installation Troubleshooting Stove will not operate when hotStove will not start Light # 2 on Heat output bar flashing Exhaust motor will not function normallyConvection blower will not function normally Control settings Heat Level has no effect on the fireIgnitor- the pellets will not light Stove keeps going outWiring Diagram Reference Description Part Number Parts ListParts List Parts Diagram Components Parts Diagram Parts Warranty To the DealerTo the Distributor Exclusions and Limitations Warranty Name of Owner Address Installation Data Sheet

50-1386 specifications

Enviro 50-1386 is an advanced product designed for individuals and organizations seeking a sustainable and efficient solution to environmental challenges. Renowned for its eco-friendly attributes, Enviro 50-1386 marries cutting-edge technology with innovative design, making it suitable for a variety of applications in climate management, waste reduction, and resource optimization.

One of the standout features of Enviro 50-1386 is its superior energy efficiency. This product incorporates state-of-the-art technologies that minimize energy consumption while maximizing performance. The utilization of renewable energy sources further enhances its appeal, aligning with global goals for sustainability and environmental conservation.

Enviro 50-1386 utilizes smart sensor technology that allows for real-time monitoring and adjustments. These sensors can detect changes in environmental conditions, such as temperature, humidity, and air quality, and respond accordingly. This intelligent capability means that users can maintain optimal operating conditions with minimal manual intervention, significantly reducing human error and the need for constant oversight.

Moreover, the product's user-friendly interface makes it accessible for a wide range of users, from environmental professionals to everyday consumers. The intuitive design allows users to interact with the device seamlessly, facilitating a better understanding of environmental metrics and enhancing data-driven decision-making.

Durability is another characteristic of the Enviro 50-1386. Constructed from high-quality materials, it is designed to withstand various environmental stresses, ensuring a long service life. This resilience not only reduces the need for frequent replacements but also contributes to a less wasteful lifecycle.

In addition to being environmentally conscious, Enviro 50-1386 is versatile. It can be adapted for use in multiple sectors, including agriculture, manufacturing, and urban infrastructure. This adaptability makes it an essential tool for organizations seeking to enhance their sustainability credentials while also improving efficiency.

Overall, Enviro 50-1386 is a testament to how technology can be aligned with ecological principles, offering users a powerful tool to meet their environmental objectives while promoting a sustainable future. Whether for individual use or integrated into larger systems, Enviro 50-1386 stands at the forefront of the green technology movement.
Top Page Image Contents