Enviro 50-1386 Convection blower will not function normally, Ignitor- the pellets will not light

Page 14

Troubleshooting

Auger light flashes but auger motor does not turn at all.

üIf the auger gear box does not turn but the motor’s armature does try to spin then the auger is jammed.

–Try to break apart jam by poking at the jam through the drop tube. If this fails then empty the hopper and remove the auger cover **remember to re-seal the cover after installation**

üCheck the fuse on the motherboard; nothing will work if the fuse is blown.

6. The convection blower will not function normally.

üClean all grill openings at the back and below unit as well as the fan blades. üContact your local dealer for service.

7. Ignitor- the pellets will not light.

(Everything else in the stove operates but the ignitor will not light the pellets.)

üMake sure the burn pot liner is up tight and square to the ignitor tube by pushing the burn pot back against the ignitor tube.

üCheck to see if the exhaust blower is operating. If not, contact your local dealer for service.

NOTE: The ignitor should be bright orange in color after about five (5) minutes. If not replace the ignitor.

8. Control settings (Heat Level) has no effect on the fire.

üNote: If the system light is flashing the control board has complete control of the unit. When the units system light becomes solid then control of the unit is given back to the operator.

üIf there is no control of the heat level button make sure the thermostat is calling for heat. üCall your local dealer for service.

9. The stove keeps going out.

a)If the stove goes out and leaves fresh unburned pellets or cigarette-like ashes in the burn pot liner, the fire is going out before the stove shuts off.

üCheck Ash build-up in the burn pot can make the auger stop. Increase the air by moving the slider to the right.

üCheck to see that the slider / damper is in the correct position.

üTurn the heat level up slightly (poor quality pellets will require slightly higher settings). üSet the auger trim till the #1 and #5 lights are illuminated.

b)If the stove goes out and there are partially burned pellets left in the burn pot liner, the stove has shut down due to a lack of air, exhaust temperature, or power failure.

üAdjust the slider / damper.

üCheck to see if the stove needs a more complete cleaning.

üTurn the heat level up slightly (poor quality pellets will require slightly higher settings). üDid the power go out?

üContact your local dealer for service.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Empress Table of Contents Introduction Automatic Safety Features Installation DimensionsRefer to Figure Side wall to center of unit Inches If installing Empress With a skirt Masonry fireplace positive flue installation Screws to move hopper Removal Slider / Damper Must be SET AT Time of Installation Stove will not start TroubleshootingStove will not operate when hot Exhaust motor will not function normally Light # 2 on Heat output bar flashingIgnitor- the pellets will not light Control settings Heat Level has no effect on the fireConvection blower will not function normally Stove keeps going outWiring Diagram Parts List Reference Description Part NumberParts List Parts Diagram Components Parts Diagram Parts To the Distributor WarrantyTo the Dealer Exclusions and Limitations Warranty Installation Data Sheet Name of Owner Address

50-1386 specifications

Enviro 50-1386 is an advanced product designed for individuals and organizations seeking a sustainable and efficient solution to environmental challenges. Renowned for its eco-friendly attributes, Enviro 50-1386 marries cutting-edge technology with innovative design, making it suitable for a variety of applications in climate management, waste reduction, and resource optimization.

One of the standout features of Enviro 50-1386 is its superior energy efficiency. This product incorporates state-of-the-art technologies that minimize energy consumption while maximizing performance. The utilization of renewable energy sources further enhances its appeal, aligning with global goals for sustainability and environmental conservation.

Enviro 50-1386 utilizes smart sensor technology that allows for real-time monitoring and adjustments. These sensors can detect changes in environmental conditions, such as temperature, humidity, and air quality, and respond accordingly. This intelligent capability means that users can maintain optimal operating conditions with minimal manual intervention, significantly reducing human error and the need for constant oversight.

Moreover, the product's user-friendly interface makes it accessible for a wide range of users, from environmental professionals to everyday consumers. The intuitive design allows users to interact with the device seamlessly, facilitating a better understanding of environmental metrics and enhancing data-driven decision-making.

Durability is another characteristic of the Enviro 50-1386. Constructed from high-quality materials, it is designed to withstand various environmental stresses, ensuring a long service life. This resilience not only reduces the need for frequent replacements but also contributes to a less wasteful lifecycle.

In addition to being environmentally conscious, Enviro 50-1386 is versatile. It can be adapted for use in multiple sectors, including agriculture, manufacturing, and urban infrastructure. This adaptability makes it an essential tool for organizations seeking to enhance their sustainability credentials while also improving efficiency.

Overall, Enviro 50-1386 is a testament to how technology can be aligned with ecological principles, offering users a powerful tool to meet their environmental objectives while promoting a sustainable future. Whether for individual use or integrated into larger systems, Enviro 50-1386 stands at the forefront of the green technology movement.
Top Page Image Contents