Installation
HORIZONTAL EXHAUST THROUGH WALL INSTALLATION:
Vent installation: install vent at clearances specified by the vent manufacturer.
A chimney connector shall not pass through an attic or roof space, closet or similar concealed spaces, or a floor, or ceiling. Where passage through a wall or partition of combustible construction is desired, the installation shall conform to
1. | Choose a location for your stove that meets |
|
|
| |||||||
| the requirements stated in this manual and |
|
| Wall | |||||||
| allows installation with the least amount of |
|
| ||||||||
|
| 4" | thimble | ||||||||
| interference to house framing, | plumbing, |
|
| |||||||
|
| (10 cm) | 12" | ||||||||
| wiring, etc. |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| (30.5 cm) | |||
2. | Install a |
|
|
| |||||||
| (where necessary). |
|
|
|
|
|
|
| |||
3. Place | the | appliance 15” (37.5 | cm) | away |
|
|
| ||||
| from the wall. If the stove is to be set on |
|
| 45° | |||||||
| a hearth pad, set the unit on it, and adjust | 6" |
| elbow | |||||||
| the leveling legs. |
|
|
|
|
|
| ||||
|
|
|
|
| (15 cm) |
|
| ||||
4. | Locate the center of the exhaust pipe on |
|
| ||||||||
|
|
| |||||||||
| the stove. Extend that line to the wall. |
|
| Rodent | |||||||
| Once you have located the center point on |
|
| mesh cap | |||||||
| the wall, refer to pellet vent manufacturer |
|
|
| |||||||
| installation instructions for correct hole size | Existing floor |
| ||||||||
| and clearance to combustibles. |
|
|
| |||||||
|
|
| floor protection. | (combustible) |
| ||||||
5. | Install | the | wall | thimble | as | per | the | Figure 11: Straight through wall Installation. | |||
| instructions written on the thimble. Maintain | ||||||||||
|
|
|
| ||||||||
| an effective vapour barrier in |
|
|
|
|
|
| ||||
| accordance with local building |
|
|
|
|
|
| ||||
| codes. |
|
|
|
|
|
|
|
|
|
|
6. | Install a length of 3” (75 mm) |
|
|
|
|
|
| ||||
| or 4” (100 mm) vent pipe into |
|
|
|
|
|
| ||||
| the wall thimble. The pipe |
|
|
|
|
|
| ||||
| should | install | easily into the |
|
|
| Exhaust Tube |
| |||
| thimble. |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| 3" (75mm) or 4" (100mm) "PL" or "L" vent | |||
7. | Connect | the | exhaust vent |
|
|
|
| ||||
|
|
|
|
|
| ||||||
| pipe to the exhaust pipe on |
|
|
|
| Wall Thimble | |||||
| the stove. Seal the connection |
|
|
|
|
|
| ||||
| with | high | temperature |
|
|
|
|
|
| ||
| silicone. |
|
|
|
|
|
|
|
|
| |
8. | Push the stove straight back, |
|
|
|
|
| 45° Elbow with screen or | ||||
| leaving a minimum of 4” (10 |
| Fresh Air Intake Tube |
| Termination Cap | ||||||
|
|
|
| ||||||||
| cm) clearance from the back |
|
|
|
|
|
| ||||
| of the stove to the wall. Seal |
|
|
|
|
|
| ||||
| the vent pipe to the thimble |
|
|
|
|
|
| ||||
| with | high | temperature |
|
|
| High Temperature RTV |
| |||
| silicone. |
|
|
|
|
|
| Silicone Required |
| ||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| Figure 12: Venting to use with straight through wall Installation. | |||
11