Enviro EF THERMO 28 #2 light is flashing. see #8 in Figure, Auger, Setting. Has lights 1

Page 21

Troubleshooting

«Contact your local Dealer for service.

«Turn the Heat Level up slightly (poor quality pellets will require slightly higher settings).

If the stove goes out and there are no pellets in the liner, the auger is stopping.

üSee “The auger motor will not function normally” and “The exhaust blower will not function normally.”

10. The #2 light is flashing. (see #8 in Figure 23)

«The water temperature high limit switch has tripped. Remove right cabinet side and manually reset the high limit switch.

«The low water pressure switch has tripped. Increase the water pressure in the system.

To reset Circuit Board after a trouble code - push the ON/OFF button

FUSES:

F1 is the fuse to the inside of the circuit board controls. If F1 has blown there may have been an input power overload or a short in the convection fan.

F2 fuse closest fuse to the outside edge of the circuit board controls. If fuse F2 has blown then there was a electrical overload problem with one of the following parts: ignitor, auger motor, high limit switch, or exhaust blower.

CONTROL BOARD FUNCTIONS:

 

 

 

 

1.

WATER TEMPERATURE DIAL: Read in degrees Celsius





2.

AUGER TRIM

 





 

 

 

 



3.

CONVECTION BLOWER CONTROL





 

 

 

�

4.

AUGER PULSE LIGHT: This light flashes in conjunction with the

 

 

 



 

auger.

 

 

 

 

 

5.

MANUAL AUGER FEED: If the unit runs out of fuel, this button can

 

 

 

be used to “prime the auger system”. This button will turn off after

 

 

 

60 seconds and then must be released and pressed again.

 

 

6.

SYSTEM LIGHT: If flashing, the board is under control. If the light

 

�

 

 

 

is solid, setting can be altered.

�

�

7.

ON/OFF BUTTON

 

 

 



8.

HEAT OUTPUT INDICATOR: Shows the present heat output

 

�

 

�

 

setting. Has lights 1 - 5.

 

9. HEAT LEVEL ADJUSTMENT: When pressed, will change the heat

 

 

 

�

 

setting of the unit from low to high.

 



 

�

�

 

 

 

 

 

 

 



NOTE: This unit is capable of continuous operation if the heat demand

Figure 23

is high enough to require the unit to stay on.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Technical Manual Table of Contents Introduction Introduction Specifications Unit Dimensions Air Bleeder Valve shown in Figure Water Temperature Limit Switch Located behind rightAsh drawer Cover Installation Installation of Expansion Tank Termination Cap Gas Meter Air Supply Inlet Restriction Zone Back wall to unit Inch Supply Horizontal Through Wall Installation Through Wall Installation Inside Vertical Installation Outside Vertical Installation Homes as well as in Air Tight homes Thermostat InstalledTroubleshooting Stove will not operate when hotStove will not start Exhaust motor will not function normally Control settings Heat Level have no effect on the fireConvection blower will not function normally Ignitor- the pellets will not lightIs solid, setting can be altered Water Temperature Dial Read in degrees CelsiusHeat Output Indicator Shows the present heat output Setting. Has lights 1Wiring Diagram Reference Part Description Part Number Parts ListParts Diagram Components Parts Diagram Body For the do-it-yourself Individual WarrantyName of Owner Address Installation Data Sheet

EF THERMO 28 specifications

The Enviro EF THERMO 28 is a cutting-edge multifuel stove that exemplifies efficient heating and contemporary design, making it an attractive option for homeowners seeking both functionality and aesthetics. This stove is engineered to optimize performance while reducing environmental impact, aligning with today’s energy-conscious lifestyles.

One of the standout features of the EF THERMO 28 is its impressive efficiency rating. It boasts an efficiency level of over 80%, ensuring that a significant portion of the fuel burned is converted into usable heat. This high efficiency minimizes fuel consumption, making it not only cost-effective but also environmentally friendly by decreasing emissions.

The stove is designed to burn a wide range of fuels, including wood, pellets, and even coal, providing users with flexibility depending on their heating needs and fuel availability. The advanced combustion system employed in the EF THERMO 28 utilizes secondary air injection, which promotes a cleaner burn and enhances overall heating performance. This technology not only contributes to lower emissions but also ensures that the stove operates effectively even in varying conditions.

Another notable characteristic of the EF THERMO 28 is its robust construction. Built from high-quality steel and equipped with a ceramic glass door, the stove is designed to withstand high temperatures while maintaining safety and durability. The design also features a large viewing window, allowing for an inviting aesthetic appeal as flames dance within the firebox.

The stove’s intuitive control system is user-friendly, featuring an adjustable air control that allows users to fine-tune the burn rate for optimal heat output. This enables more precise heating management, enhancing comfort in the home while also conserving fuel. Additionally, its compact size makes it suitable for various spaces, whether it be a rustic cabin or a modern home.

Overall, the Enviro EF THERMO 28 represents a blend of innovation, efficiency, and style. With its multifuel capabilities, high efficiency, advanced combustion technologies, and user-friendly features, this stove is an ideal choice for those looking to enhance their heating experience while adhering to eco-friendly practices. Whether for primary heating or supplementary warmth, the EF THERMO 28 provides an effective solution that caters to diverse preferences and needs in home heating.
Top Page Image Contents