Enviro C-11150 technical manual Exterior Blower Kit

Page 16

Installation

EXTERIOR MOUNTED EXHAUST BLOWER (20-070):

The Mini can be equipped with an externally mounted exhaust blower. This optional kit includes all components necessary to install the exhaust blower on any vertical wall surface.

Choose a location for your stove that meets the requirements stated in your manual and allows installation with the least amount of interference with house framing, plumbing, wiring, etc.

Included in the Exterior Mounted Exhaust Blower Kit are: 1 - Exhaust blower housing box.

1 - Blower cover plate.

1 - Hardware bag

Figure 19: Exterior Blower Kit.

Figure 20: Exterior Blower Kit.

1.Remove the left hand cabinet side by removing the two

(2)screws down the front. Loosen the three screws on the back of the cabinet side and remove panel.

2.Loosen the six (6) screws that hold the back grill in place. Lift the back grill off the screws.

3.Disconnect the Exhaust blower wires from the wire harness. Remove the exhaust blower motor from the housing; six (6) screws. Cover hole in housing with cover plate provided (see Figure 20).

4.Remove the cover from the exhaust blower housing box.

5. Install the exhaust blower housing box into the pipe placed through the wall thimble, seal with high temperature silicone. Fasten the box to the wall with (4) four screws, seal edges of box to wall with clear silicone.

6. Drill a hole through the wall thimble plate for the electrical wires. Pass the armored cable through the wall thimble. Use the strain relief provided. Do not pass cable through vent hole.

7. Install the Exhaust Blower motor into the external exhaust blower housing box. Make the electrical connections to the wire harness and exhaust blower.

8. Replace the cover on the Exhaust Box and the back grill of the stove and ensure the screws are tightened down.

9. Install vertical pipe as instructed in appropriate section.

Figure 21: Exterior Blower Kit cut-through.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Mini Table of Contents Introduction USE of Cordwood is Prohibited by LAWIntroduction Introduction Installation Screws to take out to remove stove from PalletDimensions of Mini 91.5 cm Letter Minimum Clearance Description Fresh AIR Intake 75mm Wall thimble Manufactured by pellet vent manufacturer Allows installation with the least amount Is the recommended installation set up Place a non-combustible hearth pad where Refer to Figures 17 Exterior Blower Kit Through Wall Installation with Exterior Blower Kit Sheathing Cabinet side and locate the slider damper plate. Install Special Notes Installing the Panels Kit ComponentsInstalling Hopper Lid Installing Hopper LidStove will not operate when hot TroubleshootingStove will not start Exhaust motor will not function normally 200 F 93 C high limit temperature sensor has trippedLight # 2 on Heat output bar flashing Control settings Heat Level has no effect on the fire Convection blower will not function normallyIgnitor- the pellets will not light Stove keeps going outWiring Diagram Parts List Reference Description Part NumberParts List Parts Diagram Components SDiagramPartsteel To the Dealer WarrantyTo the Distributor Exclusions and Limitations Warranty Installation Data Sheet Name of Owner Address

C-11150 specifications

Enviro C-11150 is a state-of-the-art equipment designed to address the increasing demand for efficient environmental management solutions in industrial applications. This machine stands out in the market due to its high-performance capabilities, which help businesses optimize their operations while adhering to strict environmental regulations.

One of the main features of the Enviro C-11150 is its advanced filtration system. This technology utilizes multiple stages of filtration, ensuring that even the smallest particulate matter is effectively eliminated from water, air, and other waste streams. This not only enhances the overall quality of the output but also guarantees compliance with environmental standards, minimizing the risk of penalties and fines for businesses.

The Enviro C-11150 is equipped with an innovative control system that allows for seamless monitoring and management of various environmental parameters. Users can easily access real-time data and analytics through a user-friendly interface, enabling them to make informed decisions. Additionally, the system is designed for remote monitoring, allowing operators to keep track of their processes from anywhere, enhancing operational efficiency.

Another critical characteristic of the Enviro C-11150 is its energy-efficient design. By incorporating cutting-edge technologies, the machine reduces energy consumption significantly, leading to lower operational costs for users. This is particularly important for industries looking to minimize their carbon footprint and promote sustainability in their practices.

The Enviro C-11150 also boasts a compact design, making it suitable for a variety of installation environments. Despite its small footprint, it delivers robust performance, effectively accommodating the needs of different sectors, from manufacturing to waste management.

Moreover, the machine is constructed with high-quality materials that ensure durability and longevity. This minimizes maintenance requirements and downtime, which is advantageous for businesses aiming to maintain uninterrupted operations.

In conclusion, the Enviro C-11150 is a revolutionary solution in the field of environmental management. Its advanced filtration system, innovative control technologies, energy efficiency, compact design, and durable construction collectively make it an excellent choice for industries seeking to enhance their environmental practices while maintaining high operational standards.
Top Page Image Contents