Enviro C-11150 Convection blower will not function normally, Ignitor- the pellets will not light

Page 25

Troubleshooting

7.The convection blower will not function normally.

üClean all grill openings at the back and below unit .

üPress the fan button; does the fan come on? Press again to verify that the blower turns on; if, not contact your local dealer for service.

8.Ignitor- the pellets will not light.

üEverything else in the stove operates but the ignitor will not light the pellets.

üMake sure the burn pot liner is up tight and square to the ignitor tube by pushing the burn pot back against the ignitor tube.

üCheck to see if the exhaust blower is operating. If not, contact your local dealer for service. üCheck the fuse on the circuit board.

NOTE: The ignitor should be bright orange in color. If not replace the ignitor.

9. Control settings (Heat Level) has no effect on the fire.

üNOTE: If the system light is flashing the Control Board has complete control of the unit. When the units system light becomes solid then control of the unit is given back to the operator.

üIf there is no control of the Heat Level button make sure the thermostat is calling for heat. üCall your local dealer for service.

10. The stove keeps going out.

If the stove goes out and leaves fresh unburned pellets or cigarette-like ashes in the burn pot liner, the fire is going out before the stove shuts off.

üCheck to see that the Slider / Damper is in the correct position (set with a magnehelic gauge). üTurn the Heat Level up slightly (poor quality pellets will require slightly higher settings).

üSet the auger trim till the #1 and #5 lights are illuminated.

If the stove goes out and there are partially burned pellets left in the burn pot liner, the stove has shut down due to a lack of air, exhaust temperature, or power failure.

üAdjust the Slider / Damper.

üCheck to see if the stove needs a more complete cleaning.

üTurn the Heat Level up slightly (poor quality pellets will require slightly higher settings). üDid the power go out?

üContact your local Dealer for service.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Mini Table of Contents USE of Cordwood is Prohibited by LAW IntroductionIntroduction Introduction Screws to take out to remove stove from Pallet InstallationDimensions of Mini 91.5 cm Letter Minimum Clearance Description Fresh AIR Intake 75mm Wall thimble Manufactured by pellet vent manufacturer Allows installation with the least amount Is the recommended installation set up Place a non-combustible hearth pad where Refer to Figures 17 Exterior Blower Kit Through Wall Installation with Exterior Blower Kit Sheathing Cabinet side and locate the slider damper plate. Install Special Notes Kit Components Installing the PanelsInstalling Hopper Lid Installing Hopper LidStove will not operate when hot TroubleshootingStove will not start Exhaust motor will not function normally 200 F 93 C high limit temperature sensor has trippedLight # 2 on Heat output bar flashing Convection blower will not function normally Control settings Heat Level has no effect on the fireIgnitor- the pellets will not light Stove keeps going outWiring Diagram Reference Description Part Number Parts ListParts List Parts Diagram Components SDiagramPartsteel To the Dealer WarrantyTo the Distributor Exclusions and Limitations Warranty Name of Owner Address Installation Data Sheet

C-11150 specifications

Enviro C-11150 is a state-of-the-art equipment designed to address the increasing demand for efficient environmental management solutions in industrial applications. This machine stands out in the market due to its high-performance capabilities, which help businesses optimize their operations while adhering to strict environmental regulations.

One of the main features of the Enviro C-11150 is its advanced filtration system. This technology utilizes multiple stages of filtration, ensuring that even the smallest particulate matter is effectively eliminated from water, air, and other waste streams. This not only enhances the overall quality of the output but also guarantees compliance with environmental standards, minimizing the risk of penalties and fines for businesses.

The Enviro C-11150 is equipped with an innovative control system that allows for seamless monitoring and management of various environmental parameters. Users can easily access real-time data and analytics through a user-friendly interface, enabling them to make informed decisions. Additionally, the system is designed for remote monitoring, allowing operators to keep track of their processes from anywhere, enhancing operational efficiency.

Another critical characteristic of the Enviro C-11150 is its energy-efficient design. By incorporating cutting-edge technologies, the machine reduces energy consumption significantly, leading to lower operational costs for users. This is particularly important for industries looking to minimize their carbon footprint and promote sustainability in their practices.

The Enviro C-11150 also boasts a compact design, making it suitable for a variety of installation environments. Despite its small footprint, it delivers robust performance, effectively accommodating the needs of different sectors, from manufacturing to waste management.

Moreover, the machine is constructed with high-quality materials that ensure durability and longevity. This minimizes maintenance requirements and downtime, which is advantageous for businesses aiming to maintain uninterrupted operations.

In conclusion, the Enviro C-11150 is a revolutionary solution in the field of environmental management. Its advanced filtration system, innovative control technologies, energy efficiency, compact design, and durable construction collectively make it an excellent choice for industries seeking to enhance their environmental practices while maintaining high operational standards.
Top Page Image Contents