Enviro C-11150 technical manual Introduction, USE of Cordwood is Prohibited by LAW

Page 3

Introduction

* This manual is designed for the technician in conjunction with the owner’s manual. *

RATING LABEL LOCATION:

The rating label is located on the back of the unit.

SAFETY WARNINGS AND RECOMMENDATIONS:

Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death. Any unauthorized modification of the appliance or use of replacement parts not recommended by the manufacturer is prohibited.

Caution: Do not connect to any air distribution duct or system.

Do not burn garbage or flammable fluids such as gasoline, naptha or engine oil. Unit hot while in operation. Keep children, pets, clothing and furniture away. Contact may cause skin burns.

Warning: Parts of the appliance, especially the external surfaces, will be hot to touch when in operation and due care will need to be taken. Never place wood, paper, furniture, drapes or other combustible materials within 80cm (311⁄2”) of the front of the unit, 20cm (77⁄8”) from each side, and 10cm (4”) from the back of the unit. Do not let children or pets touch it when it is hot.

To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering to the installation instructions. An ENVIRO dealer will be happy to assist you in obtaining information with regards to your local building codes and installation restrictions.

FIRE EXTINGUISHER AND SMOKE DETECTION: All homes with a pellet burning stove should have at least one fire extinguisher in a central location known to all in the household. Smoke detectors should be installed and maintained in the room containing the stove when installing and operating a pellet burning appliance. If it sounds the alarm, correct the cause but do not deactivate. You may choose to relocate the smoke detection devise within the room; DO NOT REMOVE THE SMOKE DETECTOR FROM THE ROOM.

CHIMNEY OR RUN AWAY FIRE: Call local fire department (or dial 911). Close the draft fully. Examine the flue pipes, chimney, attic, and roof of the house, to see if any part has become hot enough to catch fire. If necessary, spray with fire extinguisher or water from the garden hose. IMPORTANT: Do not operate the stove again until you are certain the chimney and its lining have not been damaged.

FUEL: This pellet stove is designed and approved to only burn wood pellet fuel with up to 3% ash content. Dirty fuel will adversely affect the operation and performance of the unit and may void the warranty. Check with your dealer for fuel recommendations.

DO NOT use this appliance as an incinerator. DO NOT use unsuitable and non recommended fuels, including liquid fuels.

THE USE OF CORDWOOD IS PROHIBITED BY LAW.

FLAMMABLE LIQUIDS: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or “freshen up” a fire in the heater. Keep all such liquids well away from the heater while it is in use.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Mini Table of Contents USE of Cordwood is Prohibited by LAW IntroductionIntroduction Introduction Screws to take out to remove stove from Pallet InstallationDimensions of Mini 91.5 cm Letter Minimum Clearance Description Fresh AIR Intake 75mm Wall thimble Manufactured by pellet vent manufacturer Allows installation with the least amount Is the recommended installation set up Place a non-combustible hearth pad where Refer to Figures 17 Exterior Blower Kit Through Wall Installation with Exterior Blower Kit Sheathing Cabinet side and locate the slider damper plate. Install Special Notes Kit Components Installing the PanelsInstalling Hopper Lid Installing Hopper LidTroubleshooting Stove will not operate when hotStove will not start 200 F 93 C high limit temperature sensor has tripped Exhaust motor will not function normallyLight # 2 on Heat output bar flashing Stove keeps going out Control settings Heat Level has no effect on the fireConvection blower will not function normally Ignitor- the pellets will not lightWiring Diagram Reference Description Part Number Parts ListParts List Parts Diagram Components SDiagramPartsteel Warranty To the DealerTo the Distributor Exclusions and Limitations Warranty Name of Owner Address Installation Data Sheet

C-11150 specifications

Enviro C-11150 is a state-of-the-art equipment designed to address the increasing demand for efficient environmental management solutions in industrial applications. This machine stands out in the market due to its high-performance capabilities, which help businesses optimize their operations while adhering to strict environmental regulations.

One of the main features of the Enviro C-11150 is its advanced filtration system. This technology utilizes multiple stages of filtration, ensuring that even the smallest particulate matter is effectively eliminated from water, air, and other waste streams. This not only enhances the overall quality of the output but also guarantees compliance with environmental standards, minimizing the risk of penalties and fines for businesses.

The Enviro C-11150 is equipped with an innovative control system that allows for seamless monitoring and management of various environmental parameters. Users can easily access real-time data and analytics through a user-friendly interface, enabling them to make informed decisions. Additionally, the system is designed for remote monitoring, allowing operators to keep track of their processes from anywhere, enhancing operational efficiency.

Another critical characteristic of the Enviro C-11150 is its energy-efficient design. By incorporating cutting-edge technologies, the machine reduces energy consumption significantly, leading to lower operational costs for users. This is particularly important for industries looking to minimize their carbon footprint and promote sustainability in their practices.

The Enviro C-11150 also boasts a compact design, making it suitable for a variety of installation environments. Despite its small footprint, it delivers robust performance, effectively accommodating the needs of different sectors, from manufacturing to waste management.

Moreover, the machine is constructed with high-quality materials that ensure durability and longevity. This minimizes maintenance requirements and downtime, which is advantageous for businesses aiming to maintain uninterrupted operations.

In conclusion, the Enviro C-11150 is a revolutionary solution in the field of environmental management. Its advanced filtration system, innovative control technologies, energy efficiency, compact design, and durable construction collectively make it an excellent choice for industries seeking to enhance their environmental practices while maintaining high operational standards.
Top Page Image Contents