Enviro C-11150 technical manual Special Notes

Page 20

Installation

SLIDER/DAMPER SET-UP:

This is used to regulate the airflow through the pellet stove. The slider damper should be set by a trained technician using magnehelic.

The slider damper is located behind the left side panel. To open the left side panel, undo the one screw

Air Intake Box

Slider Damper

Exhaust Channe

Exhaust Blower

Figure 28: Slider/Damper Plate in Unit.

located in the upper front corner of the cabinet side between the louvers. Also loosen three screws down the back of the side panel.

The combustion exhaust blower is a variable speed blower controlled by the heat output button. This blower will decrease the vacuum pressure inside the stove and as the heat output button is turned down. The vacuum pressure inside the firebox will increase as the combustion exhaust blower increases in speed (higher heat output setting).

If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the Slider Damper should be pushed in slightly, decreasing the air in the firebox.

If, after long periods of burning, the fire builds up and overflows the burn pot or there is a build up of clinkers, this would be a sign that the pellet quality is poor, this requires more primary air, the slider damper must be pulled out to compensate. Pulling the slider damper out gives the fire more air.

The easiest way to make sure that an efficient flame is achieved is to understand the characteristics of the fire.

• A tall, lazy flame with dark orange tips requires more air – Open slider (pull out) slightly.

• A short, brisk flame, like a blowtorch, has too much air – Close slider (push in) slightly.

• If the flame is in the middle of these two characteristics with a bright yellow/orange, active flame with no black tips then the air is set for proper operation (see Figure 29).

SPECIAL NOTES:

 

Pellet quality is a major factor in how the Pellet stove will operate. If

 

the pellets have a high moisture content or ash content the fire will

 

be less efficient and has a higher possibility of the fire building up

 

and creating clinkers (hard ash build-up).

Figure 29: Efficient Flame.

IMPORTANT: Taking a reading of vacuum pressure inside the firebox with a magnehelic gauge should be used to set the slider for best combustion. The slider damper should be set only on a hot stove (operating for thirty (30) minutes or more) by using a Magnahelic Pressure Gauge to measuring the pressure in the firebox. The best settings are a reading of approximately 0.11 0.12 inches of water column (27.4 - 29.9 Pa) on the high fire setting. Some fuels may require higher or lower settings. The reading can be taken from the 1⁄8” (3 mm) hole located on the front of the unit below the ash shelf.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Mini Table of Contents Introduction USE of Cordwood is Prohibited by LAWIntroduction Introduction Installation Screws to take out to remove stove from PalletDimensions of Mini 91.5 cm Letter Minimum Clearance Description Fresh AIR Intake 75mm Wall thimble Manufactured by pellet vent manufacturer Allows installation with the least amount Is the recommended installation set up Place a non-combustible hearth pad where Refer to Figures 17 Exterior Blower Kit Through Wall Installation with Exterior Blower Kit Sheathing Cabinet side and locate the slider damper plate. Install Special Notes Installing the Panels Kit ComponentsInstalling Hopper Lid Installing Hopper LidStove will not start TroubleshootingStove will not operate when hot Light # 2 on Heat output bar flashing 200 F 93 C high limit temperature sensor has trippedExhaust motor will not function normally Control settings Heat Level has no effect on the fire Convection blower will not function normallyIgnitor- the pellets will not light Stove keeps going outWiring Diagram Parts List Reference Description Part NumberParts List Parts Diagram Components SDiagramPartsteel To the Distributor WarrantyTo the Dealer Exclusions and Limitations Warranty Installation Data Sheet Name of Owner Address

C-11150 specifications

Enviro C-11150 is a state-of-the-art equipment designed to address the increasing demand for efficient environmental management solutions in industrial applications. This machine stands out in the market due to its high-performance capabilities, which help businesses optimize their operations while adhering to strict environmental regulations.

One of the main features of the Enviro C-11150 is its advanced filtration system. This technology utilizes multiple stages of filtration, ensuring that even the smallest particulate matter is effectively eliminated from water, air, and other waste streams. This not only enhances the overall quality of the output but also guarantees compliance with environmental standards, minimizing the risk of penalties and fines for businesses.

The Enviro C-11150 is equipped with an innovative control system that allows for seamless monitoring and management of various environmental parameters. Users can easily access real-time data and analytics through a user-friendly interface, enabling them to make informed decisions. Additionally, the system is designed for remote monitoring, allowing operators to keep track of their processes from anywhere, enhancing operational efficiency.

Another critical characteristic of the Enviro C-11150 is its energy-efficient design. By incorporating cutting-edge technologies, the machine reduces energy consumption significantly, leading to lower operational costs for users. This is particularly important for industries looking to minimize their carbon footprint and promote sustainability in their practices.

The Enviro C-11150 also boasts a compact design, making it suitable for a variety of installation environments. Despite its small footprint, it delivers robust performance, effectively accommodating the needs of different sectors, from manufacturing to waste management.

Moreover, the machine is constructed with high-quality materials that ensure durability and longevity. This minimizes maintenance requirements and downtime, which is advantageous for businesses aiming to maintain uninterrupted operations.

In conclusion, the Enviro C-11150 is a revolutionary solution in the field of environmental management. Its advanced filtration system, innovative control technologies, energy efficiency, compact design, and durable construction collectively make it an excellent choice for industries seeking to enhance their environmental practices while maintaining high operational standards.
Top Page Image Contents