To Install a LISTED, Factory Built Chimney

OUTSIDE AIR:

A 4” (10.16 cm) fresh air adapter kit is available. This adapter can be installed either on the back pedestal or through the floor under the pedestal.

Place the 1/4” mesh screen between the fresh air adapter and the body of the pedestal. (AS SHOWN)

NOTE: Fresh air connection to the unit must be a non combustible pipe. (Example: 4” (10.16 cm) single wall aluminum flex pipe)

NOTE: REMOVE THE 4” KNOCK OUT ON THE REAR OF THE PEDESTAL IF ROOM AIR IS TO BE USED FOR COMBUSTION AIR

ALCOVE INSTALLATION;

Model 1000 May be installed with double wall pipe in an alcove up to 4 ft. (1.2 m) deep and at least 7 ft. (2.13 m) high: sides 14” and rear 6”.

Model 1600 May be installed with double wall pipe in an alcove up to 30” (76 cm) deep and at least 70” (178 cm) high and a minimum width of 48” (122 cm)

Pedestal

rear

FLOOR PROTECTION:

If a stove is installed on a combustible floor, it must have a pedestal attached and be on a NON COMBUSTIBLE hearth pad extending at least 8” (200 mm) to each side, and 18” (455 mm) to the front as indicated below.

TO INSTALL A LISTED, FACTORY BUILT CHIMNEY.

1.Set floor protector and stove in location in accordance with the clearances required above (see previous page).

2.Mark the position for the ceiling hole by using a plumb bob.

3.Move this location, if necessary, to avoid floor joists, ceiling rafters while

still maintaining required clearances. (see manufacturer’s label on page 15 or the clearances to combustibles on page 8)

4.Mark the hole for the outside air kit.

5.Move the stove out of the way.

6.Cut a pilot hole in the ceiling.

7.Cut a hole for the ceiling penetration components and frame in the sides of the hole in both the ceiling and roof. Check, and follow chimney manufacturer’s instructions for all of these steps.

8.Install the support box and chimney through the roof. Install the slip section for the chimney connector.

9.Slip the roof flashing over the chimney and secure to the roof, being careful to keep the pipe centered in the opening. To meet the code, the chimney must extend above the roof at least 3 FT. (91.44 CM), and 2 FT. (60.9 CM) above any area of the roof, within 10 FT. (304.8 CM) of the end of the chimney.

10.Be sure all pieces including outside rain cap, flange, collar and pipe are installed and then place the stove back into position.

11.Install the smoke pipe with the lower (crimped) edge of the pipe inside the smoke collar. Any creosote formed will then run back down into the stove. All connections must be tight and secured with three sheet metal screws equally spaced.

12.Also install an outside air flex pipe to the stove.

1600INS, 1600, 1000 specifications

Enviro 1000, 1600, and 1600INS are advanced vehicles designed and manufactured by the renowned British company, Environmental Vehicle Technologies. These models are tailored for urban and semi-urban environments, offering eco-friendly transport solutions that address the growing demand for sustainable alternatives in public and commercial transport.

The Enviro 1000 model emphasizes efficiency and compactness, making it perfect for bustling city streets. This vehicle features an innovative lightweight design, which enhances fuel efficiency and reduces carbon emissions. Its state-of-the-art engine delivers a smooth and reliable driving experience while meeting stringent environmental standards. The interior is thoughtfully designed for passenger comfort, offering ergonomic seating and ample space.

The Enviro 1600 model takes sustainability a step further. Featuring an enhanced powertrain, it incorporates hybrid technology, enabling it to switch between traditional fuels and electric power seamlessly. This versatility not only lowers operating costs but also significantly decreases the vehicle's carbon footprint. The 1600 models have larger seating capacities, making them ideal for public transport systems in larger urban areas. Advanced safety features, including an automatic braking system and multiple airbag deployment, ensure the well-being of passengers and drivers alike.

Meanwhile, the Enviro 1600INS stands out with its innovative insulation technology. This additional feature enhances energy conservation, particularly useful in extreme weather conditions. The insulated body helps maintain a stable internal climate, reducing reliance on heating or air conditioning systems. This model is especially favored by transit agencies seeking to provide year-round comfort for passengers without escalating energy costs.

All Enviro models are equipped with smart technologies including real-time tracking systems, which improve route optimization and schedules, thereby enhancing overall service efficiency. They also come with fully integrated infotainment systems, ensuring passengers enjoy a pleasant travel experience.

In summary, the Enviro 1000, 1600, and 1600INS are cutting-edge vehicles designed to promote sustainable urban transport. With a focus on efficiency, enhanced safety features, hybrid technology, and innovative insulation solutions, these models epitomize the future of eco-friendly mobility, catering to the needs of modern cities while prioritizing environmental stewardship. As cities continue to grow, the demand for such versatile and sustainable vehicles will undoubtedly increase, positioning the Enviro range as frontrunners in the eco-transport revolution.