Harman Stove Company P68 Stove Temperature Mode Shut Down Procedure, Feed Adjuster Knob

Page 15

P68 AUTOMATIC IGNITION/OPERATION

Stove Temperature Mode

Shut Down Procedure

In the Stove Temperature Mode and with the igniter toggle switch in the Auto position, the stove will light automatically and can be adjusted to the desired setting using the same temperature control dial as is used in the Room Temperature Mode. The heat output and fuel consumption will remain constant regardless of room temperature. The settings from 1 to 7 on the inner ring of the dial provide for relative heat output settings with 1 being low and 7 being the maximum.

In Stove Temperature Mode the stove will not automatically shut off unless the stove runs out of fuel or is turned off.

Never pull the plug to shut down the stove. This will stop the combustion blower and smoke will escape through window and door gaskets.

When the igniter toggle switch is set to manual in this mode, the distribution blower will not turn on with a temperature dial setting from 1 to 5. The advantage of this mode is to allowthe operator to have a large viewing fire without blowing extra heat into the room.

During operation, with the temperature dial set at #5 or less, the distribution fan will not operate. A #5 on the temperature dial and a #5 on the feed adjuster is approximately 80% output. It is not necessary to oper- ate the distribution blower below this point. Therefore, the control allows a higher burn rate ( a larger viewing fire) without an excess of hot air blowing into the room.

An example of when to use the Manual Stove Tem- perature Mode is if you want to watch a large fire and the room is already up to temperature. The Stove Tem- perature Mode allows you to have a larger fire and a lower sound level, without the distribution blower.

NOTE: During the use of this mode, if you keep increasing the temperature dial setting to increase the fire size, the distribution blower will automati- cally come on when the ESP Temperature reaches 350o F, or 81% output.

Feed Adjuster Knob

For most premium grade pellet fuels the Feed Adjuster Knob should be set at 4. If higher ash fuels are used the setting should be increased to 5 or 6. Also higher settings are required if you would like to get the maximum heat output from the stove. At the maximum burn rate (with the temperature dial on 7/90° and the feed adjuster at 6) there should be 1" or more of ash on the front of the burn pot. If there is less than 1" of ash, turn the feed adjuster knob down to a lower setting.

The best way to shut down the stove is simply let it run

out of pellets, the stove will shut down automatically. Alternatively, you can turn the Mode Selector to “off”.

This will cause the fire to gradually die down and go out. The fire will not go out immediately and may take more than an hour to fully shut down.

If the stove is left to run out of fuel, you may get a 6 blink status light. If this happens simply reset the control board by turning the mode selector to OFF and back ON.

Stove Temperature Mode

This setting,see below, will produce continuous medium heat output with the distribution blower at low speed.

This setting, see below, will produce continuous maximum heat output with the distribution blower at full speed.

P68 Pellet Stove 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Safety Notice Installation & Operating ManualP68 Pellet Stove Introduction Table of ContentsImportant Notes Door Handle Installation Assembly and InstallationInstalling InstallationAddition, the following must be observed With outside air installedWith outside air installed, 6 feet VentingVent Pipe VentingHRV Outside Air#1 Preferred method #2 Preferred methodThroughs #5 Installing into an existing fireplace chimney US only #4 Installing into an existing chimney US only#7 Installing into an existing chimney US and Canada #8 Installing through the ceiling Minimum flue vent configurationP68 Automatic IGNITION/OPERATION Room Temperature ModeFeed Adjuster Knob Stove Temperature Mode Shut Down ProcedureP68 Automatic Start UP Igniter Switch toAUTOup positionTurn Mode Selector to OFF Turn Feed Adjuster to #4.4Room Temperature Mode Stove Temperature ModeP68 Manual IGNITION/OPERATION Igniter Switch toMANUAL down position P68 Manual Start UPFill hopper with pellets and remove ashes as required.1 P68 Automatic Ignition ESP Control Status light error messagesLow Draft Voltage Adjustment P68 Low Draft Voltage AdjustmentRoom Sensor and Rear Shield Installation Room Sensor InstallationRear Shields Removing Ashes MaintenanceCleaning the Door Glass CleaningSoot and FlyAsh Cause a House FireBurn Pot Cleaning and Maintenance P68 Maintenance Burn PotP68 Maintenance Gasket Adjustment P68 Maintenance Cleaning the Feeder Body Cleaning Burn Pot P68 Trouble-ShootingSpecifications P68 Feeder and SpecificationsHopper Extension OptionsSide Heat Shields Floor ProtectorP68 Wiring Diagram Description Part Number P68 Parts ListYear Limited Warranty Commercial Harman Gold Warranty

P68 specifications

The Harman Stove Company P68 is a high-efficiency pellet stove that stands out for its blend of advanced technology and user-friendly features. Designed for both comfort and convenience, the P68 offers a remarkable heating capacity while maintaining an appealing aesthetic that fits well with a variety of home interiors.

One of the key features of the P68 is its impressive heating capability. With the ability to produce up to 68,000 BTUs, this stove can effectively heat spaces of up to 3,800 square feet. This makes it an excellent choice for both residential and larger commercial environments. The P68’s large hopper capacity, capable of holding up to 68 pounds of pellets, allows for extended burn times, providing homeowners with less frequent refueling.

The stove is equipped with Harman’s patented Smart Control technology, which optimizes fuel efficiency and heat output. This intelligent control system continuously monitors the burn rate and adjusts the feed rate of pellets accordingly. This ensures a consistent and comfortable temperature while minimizing waste. Users can also take advantage of the intuitive digital control panel, which allows for easy temperature adjustments and programming options.

In terms of design, the P68 is as functional as it is stylish. It features a large viewing window, allowing users to enjoy the beauty of the flames and create a cozy atmosphere. The stove is also available in multiple color finishes, ensuring it can complement any home decor.

Another standout characteristic of the P68 is its ease of maintenance. The design includes a removable ash pan for quick and straightforward cleaning. Furthermore, the patented burn pot design minimizes clinkers, reducing the need for frequent maintenance.

The Harman Stove Company P68 also emphasizes safety with its built-in safety features, including a pressure switch that monitors venting blockages, ensuring safe operation. With its combination of high efficiency, advanced technology, and user-friendly design, the P68 is an excellent choice for anyone looking to enhance their home heating system while prioritizing both comfort and style. Whether for a chilly winter evening or a cozy family gathering, the Harman P68 continues to be a superior option for pellet heating solutions.
Top Page Image Contents