Harman Stove Company owner manual P68 Maintenance Gasket Adjustment

Page 25

P68 Maintenance - Gasket Adjustment

Your new Harman Stove viewing door gasket has been factory set, however over a period of time some minor adjustment may be necessary. The easiest way to check the adjustment of the door gasket is to take a small piece of paper or a dollar bill (when the stove is not burning) and open the door, place the paper between the face of stove body and the gasket at the top center of the door, close the door. You should have a slight amount of resistance when you try to pull the paper out. Repeat this process on the bottom center of the door. If the paper is loose then some adjustment is necessary.

To adjust the door, the stove must be turned off and cold. Open the door, loosen the 2 bolts shown (see Fig. 37) and bump the latch adjuster (Fig. 38) toward the back of stove, snug bolts and test for proper seal as described above. Once the proper seal is attained, open the door and finish tightening the bolts. If proper adjustment cannot be accomplished, then a new gasket should be installed.

Over a period of time the gasket will wear out and a new gasket will have to be installed. To install a new gasket you must remove the old gasket. After the gasket is removed the gasket channel should be free of all loose particles. The gasket cement used to hold the gasket in place is RTV (HIGH TEMPERATURE) silicone. Put a bead of RTV silicone in the bottom of the gasket channel, then install the new gasket and close the door. Allow to dry for several hours before lighting the stove. After the RTV silicone has cured, the door will have to be adjusted for proper sealing. If you have just replaced the door gasket, the latch adjuster must be pulled towards the front of the stove. Follow the procedure mentioned above.

Bolts

Fig. 37

Latch Adjuster

Fig. 38

P68 Pellet Stove 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Safety Notice Installation & Operating ManualP68 Pellet Stove Introduction Table of ContentsImportant Notes Door Handle Installation Assembly and InstallationInstalling InstallationWith outside air installed, 6 feet With outside air installedVenting Addition, the following must be observedVent Pipe VentingHRV Outside Air#2 Preferred method #1 Preferred methodThroughs #5 Installing into an existing fireplace chimney US only #4 Installing into an existing chimney US only#7 Installing into an existing chimney US and Canada #8 Installing through the ceiling Minimum flue vent configurationP68 Automatic IGNITION/OPERATION Room Temperature ModeFeed Adjuster Knob Stove Temperature Mode Shut Down ProcedureTurn Mode Selector to OFF Igniter Switch toAUTOup positionTurn Feed Adjuster to #4.4 P68 Automatic Start UPStove Temperature Mode Room Temperature ModeP68 Manual IGNITION/OPERATION P68 Manual Start UP Igniter Switch toMANUAL down positionFill hopper with pellets and remove ashes as required.1 P68 Automatic Ignition ESP Control Status light error messagesLow Draft Voltage Adjustment P68 Low Draft Voltage AdjustmentRoom Sensor Installation Room Sensor and Rear Shield InstallationRear Shields Cleaning the Door Glass MaintenanceCleaning Removing AshesSoot and FlyAsh Cause a House FireBurn Pot Cleaning and Maintenance P68 Maintenance Burn PotP68 Maintenance Gasket Adjustment P68 Maintenance Cleaning the Feeder Body Cleaning Burn Pot P68 Trouble-ShootingSpecifications P68 Feeder and SpecificationsSide Heat Shields OptionsFloor Protector Hopper ExtensionP68 Wiring Diagram Description Part Number P68 Parts ListYear Limited Warranty Commercial Harman Gold Warranty

P68 specifications

The Harman Stove Company P68 is a high-efficiency pellet stove that stands out for its blend of advanced technology and user-friendly features. Designed for both comfort and convenience, the P68 offers a remarkable heating capacity while maintaining an appealing aesthetic that fits well with a variety of home interiors.

One of the key features of the P68 is its impressive heating capability. With the ability to produce up to 68,000 BTUs, this stove can effectively heat spaces of up to 3,800 square feet. This makes it an excellent choice for both residential and larger commercial environments. The P68’s large hopper capacity, capable of holding up to 68 pounds of pellets, allows for extended burn times, providing homeowners with less frequent refueling.

The stove is equipped with Harman’s patented Smart Control technology, which optimizes fuel efficiency and heat output. This intelligent control system continuously monitors the burn rate and adjusts the feed rate of pellets accordingly. This ensures a consistent and comfortable temperature while minimizing waste. Users can also take advantage of the intuitive digital control panel, which allows for easy temperature adjustments and programming options.

In terms of design, the P68 is as functional as it is stylish. It features a large viewing window, allowing users to enjoy the beauty of the flames and create a cozy atmosphere. The stove is also available in multiple color finishes, ensuring it can complement any home decor.

Another standout characteristic of the P68 is its ease of maintenance. The design includes a removable ash pan for quick and straightforward cleaning. Furthermore, the patented burn pot design minimizes clinkers, reducing the need for frequent maintenance.

The Harman Stove Company P68 also emphasizes safety with its built-in safety features, including a pressure switch that monitors venting blockages, ensuring safe operation. With its combination of high efficiency, advanced technology, and user-friendly design, the P68 is an excellent choice for anyone looking to enhance their home heating system while prioritizing both comfort and style. Whether for a chilly winter evening or a cozy family gathering, the Harman P68 continues to be a superior option for pellet heating solutions.
Top Page Image Contents